cisco 7609 configuration manual

For example, you can abbreviate the show command to sh and the configure terminal command to config t. Enter a question mark (?) to see the available ROM-monitor commands. For more information about the ROM-monitor commands, refer to the Cisco 7600 Series Router Cisco IOS Command Reference publication. Step 3 Check and verify the entire list of configuration parameters, which should display on your console. To send data to another subnet when the router is not configured with a routing protocol, configure a default gateway. When the router boots, it automatically retrieves the IP address from the BOOTP server. After you specify the level and set a password, give the password only to users who need to have access at this level. You can configure up to 16 hierarchical levels of commands for each mode. By configuring multiple passwords, you can allow different sets of users to have access to specified commands. If you want more restricted access to the configure command, you can assign it level 3 security and distribute that password to more restricted users. For complete syntax and usage information for the ROM monitor commands, refer to the Cisco 7600 Note Series Router Cisco IOS Command Reference publication. In ROM-monitor mode, enter the o command to verify the value of the configuration register boot field. For detailed file management configuration information, refer to the Cisco IOS Configuration Fundamentals Configuration Guide at this URL: The redundant supervisor engine runs in EHSA standby mode. Note The EHSA feature is not supervisor engine mirroring or load balancing. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. The MSFC and PFC on the redundant supervisor engine come out of reset but are not operational. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04.

• cisco 7609 configuration guide, cisco 7609 router configuration guide, cisco 7609 configuration manual, cisco 7609 configuration manual pdf, cisco 7609 configuration manual download, cisco 7609 configuration manual free, cisco 7609 configuration manual downloads.

Audience This guide is for experienced network administrators who are responsible for configuring and maintaining Cisco 7600 series routers. Chapter 23 Configuring Network Security Describes how to configure network security features that are unique to the Cisco 7600 series routers. Chapter 24 Configuring Denial of Service Describes how to configure denial of service Protection protection. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation on the World Wide Web at this URL: You can access the Cisco website at this URL: Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a login ID or password, register at this URL: Priority 1 (P1)—Your network is “down” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation. You can access the Internet Protocol Journal at this URL: Note For more information about web access to the router, refer to “Using the Cisco Web Browser” in the IOS Configuration Fundamentals Configuration Guide at this URL: Note For complete syntax and usage information for the commands used in this chapter, refer to the Cisco 7600 Series Router Cisco IOS Command Reference publication and the Release 12.1 publications. Step 3 Initiates enable mode enable.History substitution allows you to access these commands without retyping them, by using special abbreviated commands. Table 2-2 lists the history substitution commands. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. The commands available to you depend on which mode you are currently in. To get a list of the commands in a given mode, type a question mark (?) at the system prompt. You can abbreviate commands and keywords by entering just enough characters to make the command unique from other commands.

Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 6-19. The configuration tasks in this chapter apply to LAN ports on LAN switching modules and to the LAN ports on the supervisor engine. Switching Frames Between Segments Each LAN port on a Cisco 7600 series router can connect to a single workstation or server, or to a hub through which workstations or servers connect to the network. Use the trunk or nonegotiate keywords to force LAN ports in different domains to trunk. For more information on VTP domains, see Chapter 8, “Configuring VTP.” Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. You must configure the neighboring port manually as a trunk port to establish a trunk link. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. The BPDUs on the native VLAN of the trunk are sent untagged to the reserved IEEE 802.1d spanning tree multicast MAC address (01-80-C2-00-00-00). The BPDUs on all other VLANs on the trunk are sent tagged to the reserved Cisco Shared Spanning Tree (SSTP) multicast MAC address (01-00-0c-cc-cc-cd). Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. Reverts to the default value (VLAN 1).Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 7-14 78-14064-04. Note For complete syntax and usage information for the commands used in this chapter, refer to the Cisco 7600 Series Router Cisco IOS Command Reference publication. By default, the Cisco 7600 series router is in VTP server mode and is in the no-management domain state until the router receives an advertisement for a domain over a trunk link or you configure a management domain. On devices that do not support VTP pruning, you must manually configure the VLANs allowed on trunks. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04.

Network services are disrupted until the redundant supervisor engine takes over and the router recovers.If they are not identical, one will boot first and become active and hold the other supervisor engine and MSFC in a reset condition. Note If you are performing a first-time upgrade to RPR from EHSA, you must reload both supervisor engines. On the Cisco 7600 series router, the port numbers always begin with 1. When facing the rear of the router, ports are numbered from the left to the right. Processor board ID SAD04430J9K R7000 CPU at 300Mhz, Implementation 39, Rev 2.1, 256KB L2, 1024KB L3 Cache Last reset from power-on Bridging software. You can enter the show running-configuration command to display the configured VLAN interfaces. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. Wait until the command prompt reappears before exiting interface-range configuration mode. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. Table 6-1 shows the four possible link negotiation configurations and the resulting link status for each configuration. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 6-11. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 6-12 78-14064-04. When a module has been removed or installed, the Cisco 7600 series router stops processing traffic for the module and scans the system for a configuration change. Each interface type is verified against the system configuration, and then the system runs diagnostics on the new module. Note The clear counters command clears counters displayed with the EXEC show interfaces command, not counters retrieved using SNMP. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 6-18 78-14064-04. An interface that has been shut down is shown as administratively down in the show interfaces command display.

MAC address reduction allows only discrete levels Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 10-3. Note For complete syntax and usage information for the commands used in this chapter, refer to the Cisco 7600 Series Router Cisco IOS Command Reference publication for this release. The sound quality of a Cisco IP Phone call can deteriorate if the voice traffic is transmitted unevenly. The default Layer 2 CoS value is 0. Untrusted mode is the default. The supervisor engine initially allocates the configured default of 7 W (167 mA at 42V) to the Cisco IP Phone. When the correct amount of power is determined from the CDPv2 messaging with the Cisco IP Phone, the supervisor engine reduces or increases the allocated power. The Policy Feature Card 2 (PFC2) and any Distributed Feature Cards (DFCs) provide hardware support for policy-based routing (PBR) for route-map sequences that use the match ip address and set ip next-hop keywords. All LAN ports in each EtherChannel must be the same speed and must all be configured as either Layer 2 or Layer 3 LAN ports. LACP supports the automatic creation of EtherChannels by exchanging LACP packets between LAN ports. LACP packets are exchanged only between ports in passive and active modes. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 13-3 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 13-4 78-14064-04. LACP does not support half-duplex. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 13-5 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 13-6 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 13-10 78-14064-04. This chapter describes how to configure IEEE 802.1Q tunneling and Layer 2 protocol tunneling on the Cisco 7600 series routers. The PDU is then flooded to the native VLAN of the Layer 2 tunnel port.

You enable pruning globally on the Cisco 7600 series router (see the “Enabling VTP Pruning” section on page 8-7). Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. On Cisco 7600 series routers with trunk connections to network devices in VTP transparent mode, configure the VLANs that are used by the transparent-mode network devices or that need to be carried across trunks as pruning ineligible. Do not enable VTP version 2 unless every network device in the VTP domain supports version 2. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. You cannot clear the domain name. Note Step 3 Exits VLAN configuration mode.For complete syntax and usage information for the commands used in this chapter, refer to the Note Cisco 7600 Series Router Cisco IOS Command Reference publication. Some of these VLANs are propagated to other switches in the network when you use the VLAN Trunking Protocol (VTP). Note When a Cisco 7600 series router is configured as a VTP server, you can configure Token Ring VLANs from the router. Token Ring TrBRF VLANs. The TrBRF can function as a source-route bridge (SRB) or a source-route transparent (SRT) bridge running either the IBM or IEEE STP. If an SRB is used, you can define duplicate MAC addresses on different logical rings. When the ISL connection is reestablished, all but one port in the backup TrCRF is disabled. Figure 9-4 illustrates the backup TrCRF. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 78-14064-04. For information on configuring VTP, see Chapter 8, “Configuring VTP.”. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 9-12 78-14064-04. These restrictions apply when mapping 802.1Q VLANs to ISL VLANs: You can configure up to eight 802.1Q-to-ISL VLAN mappings on the Cisco 7600 series router. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 10-2 78-14064-04.

For complete syntax and usage information for the commands used in this chapter, refer to the Note Cisco 7600 Series Router Cisco IOS Command Reference publication.Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 16-2. Figure 16-1 UplinkFast Example Before Direct Link Failure Switch A Switch B (Root) Blocked port Switch C Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 16-3 78-14064-04. The Layer 2 LAN interface on Switch C that connects directly to Switch B is in the blocking state. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 16-4. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 16-5. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 16-7 78-14064-04. Connecting hubs, concentrators, switches, bridges, etc.Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 16-14 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 17-4 78-14064-04. Cisco IOS CEF and dCEF are permanently enabled on the MSFC2. No configuration is required to support hardware Layer 3 switching. The Cisco IOS CEF ip load-sharing per-packet, ip cef accounting per-prefix, and ip cef accounting non-recursive commands on the MSFC2 apply only to traffic that is CEF-switched in software on the MSFC2. Note Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 17-6 78-14064-04. For more information on the syntax and usage for the commands used in this chapter, refer to the Note Cisco 7600 Series Router Cisco IOS Command Reference publication. In systems with Distributed Forwarding Cards (DFCs), IP multicast flows are Layer 3 switched locally using Multicast Distributed Hardware Switching (MDHS). Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 18-3 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 18-4 78-14064-04. Traffic that fails the RPF check is called non-RPF traffic.

The Cisco 7600 series router processes non-RPF traffic in hardware on the PFC by filtering (dropping) or rate limiting the non-RPF traffic. CEF-based rate limiting of RPF failures is the default on systems with PFC2 and for DFCs. NetFlow-based rate limiting of RPF failures is the only rate limiting mode supported with PFC1. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 18-6 78-14064-04. For details on configuring IGMP snooping, see Chapter 21, “Configuring IGMP Snooping.” Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 18-7 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 18-8 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 18-9 78-14064-04. Step 2 Selects the Layer 3 interface to be configured.Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 18-14. For an example of the show mls ip multicast statistics command, see the “Displaying IP Multicast Layer 3 Switching Statistics” section on page 18-17. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 18-19 78-14064-04. Note For complete syntax and usage information for the commands used in this chapter, refer to the Cisco 7600 Series Router Cisco IOS Command Reference publication.IP MLS switches unicast IP data packet flows between IP subnets using advanced application-specific integrated circuit (ASIC) switching hardware, which offloads the processor-intensive packet routing from network routers. The PFC forwards the rewritten packet to Host B’s VLAN (the destination VLAN is stored in the MLS cache entry) and Host B receives the packet. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 19-4 78-14064-04. Enabling IP MLS Globally IP MLS is enabled globally and cannot be disabled. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 19-6 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.

If you enable Layer 2 protocol tunneling on a port, PDUs of an enabled protocol are not sent out. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 14-8. Note For complete syntax and usage information for the commands used in this chapter, refer to the Cisco 7600 Series Router Cisco IOS Command Reference publication. Cisco 7600 series routers use STP (the IEEE 802.1D bridge protocol) on all VLANs. By default, a single instance of STP runs on each configured VLAN (provided you do not manually disable STP). You can enable and disable STP on a per-VLAN basis. To view the MAC address range on your chassis, enter the show catalyst6000 chassis-mac-address command. Configuring a higher value increases the probability; a lower value decreases the probability. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-4 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-5. They must allow the frame lifetime to expire for frames that have been forwarded using the old topology.If properly configured, each Layer 2 LAN port stabilizes to the forwarding or blocking state. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-8 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-10 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-11 78-14064-04. In a network of Cisco network devices connected through 802.1Q trunks, the network devices maintain one instance of STP for each VLAN allowed on the trunks. However, non-Cisco 802.1Q network devices maintain only one instance of STP for all VLANs allowed on the trunks. In Cisco IOS release 12.1(13)E and later releases, RSTP is also available as a standalone protocol in Rapid-Per-VLAN-Spanning Tree (Rapid-PVST) mode.In Cisco IOS release 12.1(13)E and later releases, RSTP is also available as a standalone protocol in Rapid-Per-VLAN-Spanning Tree (Rapid-PVST) mode.

This extension provides both rapid convergence and load balancing in a VLAN environment.Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-17 78-14064-04. In a Cisco 7600 series router running MST, IST (instance 0) corresponds to CST. Other bridges on the boundary that belong to the same region eventually block the boundary ports that lead to the root. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-19 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-20 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-21 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-22. You can enable STP on a per-VLAN basis. The Cisco 7600 series router maintains a separate instance of STP for each VLAN (except on VLANs on which you disable STP). Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-24 78-14064-04. Configuring the Root Bridge Cisco 7600 series routers maintain a separate instance of STP for each active VLAN. A bridge ID, consisting of the bridge priority and the bridge MAC address, is associated with each instance. For each VLAN, the network device with the lowest bridge ID becomes the root bridge for that VLAN. Cisco IOS uses the port priority value when the LAN port is configured as an access port and uses VLAN port priority values when the LAN port is configured as a trunk port. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-30 78-14064-04. To configure the switch in Rapid-PVST mode, see the “Configuring STP” section on page 15-22. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-33 78-14064-04. Clears the MST configuration.Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 15-40.

1E 19-11 78-14064-04. The detailed option displays the breakdown of contention between different flows. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 19-12. Note Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 19-14 78-14064-04. For complete syntax and usage information for the commands used in this chapter, refer to the Note Cisco 7600 Series Router Cisco IOS Command Reference publication.IPX MLS switches unicast IPX data packet flows between networks using advanced application-specific integrated circuit (ASIC) switching hardware, offloading processor-intensive packet routing from network routers. The PFC checks the MLS cache and finds the entry matching the flow in question. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 20-3. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 20-4. See the “Configuring the MLS Aging Time” section on page 33-10. IPX MLS does not use fast aging. Note Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 20-7 78-14064-04. The detailed option displays the breakdown of contention between different flows. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 20-11 78-14064-04. Refer to the Cisco IOS IP and IP Routing Configuration Guide, Release 12.1, “IP Multicast,” “Configuring IP Multicast Routing,” at this URL: Multicast group membership lists can consist of both static and IGMP snooping-learned settings. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 21-2 78-14064-04. Any known multicast traffic is forwarded to the group and not to the CPU. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 21-3 78-14064-04. You can enable the IGMP snooping querier on all the Cisco 7600 series routers in the VLAN, but for each VLAN that is connected to switches that use IGMP to report interest in IP multicast traffic, you must set at least one switch as the IGMP snooping querier.

You can enable the IGMP snooping querier on all the Cisco 7600 series routers in the VLAN.Note To enable IP multicast routing on the Cisco 7600 series routers on a specific VLAN, enter the ip pim sparse-mode command, the ip pim sparse-dense-mode command, or the ip pim dense-mode command on that interface. IGMP snooping allows Cisco 7600 series routers to examine IGMP packets and make forwarding decisions based on their content.The ip igmp snooping mrouter interface command, which was available in earlier releases and which provided the same functionality as the mac-address-table static command, is deprecated in Release 12.1(13)E and later releases. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 21-10 78-14064-04. To display multicast router interfaces, perform this task: Command Purpose Displays multicast router interfaces.When an RGMP join message is sent, the router is able to receive multicast data. When RGMP is disabled on the router, all multicast data traffic is sent to the router by the Cisco 7600 series router. Note With Release 12.1(11b)E and later releases, when you are in configuration mode you can enter EXEC. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 23-2 78-14064-04. On a network device other than a Cisco 7600 series router, when ports are configured to deny traffic, CBAC permits traffic to flow bidirectionally through the port if it is configured with the ip inspect command. The same behavior. To permit the traffic. Unlike regular Cisco IOS standard or extended ACLs that are configured on router interfaces only and are applied on routed packets only, VACLs apply to all packets and can be applied to any VLAN or WAN interface. VACLS are processed in hardware. Figure 23-1 Applying VACLs on Bridged Packets VACL Bridged Host A Catalyst 6500 Series Switch Host B with PFC (VLAN 10) (VLAN 10) Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 23-9 78-14064-04.

VACLs applied to WAN interfaces do not support the drop, forward, or redirect actions.A flow is defined as packets with the same IP addresses and Layer 4 (UDP or TCP) port numbers. When a log message is generated, the timer and packet count is reset. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 23-17. With Supervisor Engine 1 and PFC, TCP intercept flows are processed in software. For configuration procedures, refer to the Cisco IOS Security Configuration Guide, Release 12.1, “Traffic Filtering and Firewalls,” “Configuring TCP Intercept,” at this URL: Configuring Unicast RPF For configuration procedures, refer to the Cisco IOS Security Configuration Guide, Release 12.1, “Other Security Features,” “Configuring Unicast Reverse Path Forwarding” at this URL: Note When you enter the ip verify unicast source reachable-via command, the Unicast RPF checking mode changes on all ports in the router. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 23-20 78-14064-04. The Cisco 7600 series routers use forwarding tables to direct traffic to specific ports based on the VLAN number and the destination MAC address of the frame. When there is no entry corresponding to the frame’s destination MAC address in the incoming VLAN, the frame is sent to all forwarding ports within. The information covered in this chapter is unique to the Cisco 7600 series routers, and it supplements the network security information and procedures in the “Configuring Network Security”. Security ACLs The Cisco 7600 series router can deny packets in hardware using security ACLs and can drop DoS packets before they reach the CPU inband datapath. Because security ACLs are applied in hardware using the TCAM, long security ACLs can be used without impacting the throughput of other traffic. Most of these packets are dropped, but a small number are sent to the router (rate limited). Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 24-5 78-14064-04.

For complete syntax and usage information for the commands used in this chapter, refer to the Note Cisco 7600 Series Router Cisco IOS Command Reference publication.You can enable 802.1X on a SPAN source port. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 25-6 78-14064-04. For more information, refer to the Cisco IOS Security Configuration Guide, Release 12.1, publication and the Cisco IOS Security Command Reference, Release 12.1, publication at this URL:. A failed authentication of the client might occur because the client provided an invalid password. You can provide a faster response time to the user by entering a smaller number than the default. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 25-11 78-14064-04. If the router does not receive this notification, the router waits a set period of time, and then retransmits the frame. For detailed information about the fields in these displays, refer to the Cisco 7600 Series Router Cisco IOS Command Reference publication. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 26-3 78-14064-04. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 26-4. The show storm control and show port-security privileged EXEC commands display those features. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 26-5 78-14064-04. Layer 3 protocol filtering does not support the features available with standard and extended Cisco IOS ACLs. Layer 2 protocols, such as Spanning Tree Protocol (STP) and Cisco Discovery Protocol (CDP), are not affected by Layer 3 protocol filtering. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 27-3 78-14064-04. For earlier releases, refer to Chapter 29, “Configuring Broadcast Suppression.”. Disables multicast traffic storm control on the interface.You must use one of the traffic-type keywords: broadcast, multicast, or unicast, which all display the same discard count.

Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 28-4 78-14064-04. Releases earlier than Release 12.1(12c)E1 support broadcast suppression. Use traffic storm control with Release 12.1(12c)E1 and later releases (see Chapter 28, “Configuring Traffic Storm. Broadcast suppression on the Cisco 7600 series routers is implemented in hardware. The suppression circuitry monitors packets passing from a LAN interface to the switching bus. Using the. CDP allows network management applications to discover Cisco devices that are neighbors of already known devices, in particular, neighbors running lower-layer, transparent protocols. The display can be limited to neighbors on a specific interface and expanded to provide more detailed information. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 30-3 78-14064-04. Note For complete syntax and usage information for the commands used in this chapter, refer to the Cisco 7600 Series Router Cisco IOS Command Reference publication. If the packets are echoed back within a specific time frame and they are lacking a specific acknowledgment (echo), the link is flagged as unidirectional and the LAN port is shut down. Note Individual LAN port configuration overrides the setting of this command. Disables UDLD globally on fiber-optic LAN ports.Step 3 Verifies the configuration.Note For complete syntax and usage information for the commands used in this publication, refer to the Cisco 7600 Series Router Cisco IOS Command Reference publication.On the Cisco 7600 series routers, queue architecture and QoS queueing features such as Note Weighted-Round Robin (WRR) and Weighted Random Early Detection (WRED) are implemented with a fixed configuration in Application Specific Integrated Circuits (ASICs). Policing can mark or drop traffic. Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E 32-4 78-14064-04.

cisco 7200 manual

If the remote end of the WAN connection is connected and properly configured, the AutoInstall process begins. Perform the following step to complete this task. If you fail to do this, your configuration will be lost the next time you reload the router. These parameters are used for controlling system-wide settings. Complete the following steps to enter the global parameters: The following information appears after about 30 seconds. When you see this information, you have successfully booted your router: On subsequent uses of the setup facility, the script begins with a System Configuration Dialog as shown in the following example. Method Status ProtocolFor Internet Protocol (IP)-only installations, you can accept the default values for most of the questions. A typical configuration using IP, IPX, and AppleTalk follows and continues through Step 8: It provides a means to access and set configuration and run-time parameters of routers and communication servers. SNMP defines a set of functions that can be used to monitor and control network elements. If you are using IP routing, you must also select an interior routing protocol. You can specify only one of two interior routing protocols to operate on your system using the setup facility: Interior Gateway Routing Protocol (IGRP) or Routing Information Protocol (RIP). Only IP, IPX, and AppleTalk are the selected protocols for this example. This is done by using the media-type interface command: Changing the speed and duplex of an NPE-G1 or NPE-G2 Gigabit Ethernet interface is done using the speed and duplex interface commands. This is useful for connecting to other Gigabit Ethernet equipment that does not support 802.1z autonegotiation. Both full-duplex and half-duplex operation are supported in this mode. In this example, the first interface is configured for the GBIC media type, the second interface is configured for the RJ-45 media type, and the third interface is not used.

• cisco 7200 manual, cisco vxr 7200 manual, cisco 7200 manual, cisco 7200 manual download, cisco 7200 manual pdf, cisco 7200 manual software, cisco 7200 manual downloads.

The chapter contains the following sections: Complex configuration procedures are beyond the scope of this publication and can be found in the modular configuration and modular command reference publications in the Cisco IOS software configuration documentation set that corresponds to the software release installed on your Cisco hardware. The green OK LED on the power supply turns on. The LEDs on most of the port adapters go on and off in irregular sequence. If the Port Adapter Jacket Card is installed, observe its LEDs. Some may go on, go out, and go on again for a short time.During this initialization, the LEDs on each port adapter behave differently (most flash on and off). On the console terminal, after the system displays the system banner and hardware configuration, you will see the following System Configuration Dialog prompt: You do not have to configure the interfaces immediately; however, you cannot enable the interfaces or connect them to any networks until you have configured them. To verify correct operation of each interface, complete the first-time startup procedures and configuration, and then refer to the configuration note for each port adapter for LED descriptions and to check the status of the interfaces. You can configure features such as Access Control Lists (ACLs), routing protocols, and other options using SDMs advanced mode. SDM does not support the following features: WAN configuration, Gigabit Ethernet (GE) interfaces, AA client, EZ VPN server, QoS, SSHv2, DHCP server configuration options, and usability enhancements. If your router did not ship with SDM preinstalled, you can download a free copy from the Software Center at Cisco.com at Because SDM uses a GUI, it requires that you access it from a PC using a supported web browser. Go to the Security Device Manager (SDM), Version 1.1 User Note for the 7xxx Routers for more information. The show version command displays the release of Cisco IOS software that is available on the router.

You might need to reload the system image by power cycling the router. This allows you to log in without using a password and to display the startup configuration passwords. However, after powering off the router, wait at least 30 seconds before powering it on again. Note the value for use later and proceed to Step 6. If you cannot log in to the router at all, go to the next step. Proceed to Step 6. If Break is disabled, power cycle the router (turn the router off or unplug the power cord, and then restore power). Then proceed to Step 5. The user EXEC prompt is displayed as follows: Then enter the show startup-config command to display the passwords in the configuration file as follows: The passwords displayed look something like this: The enable and console login passwords may be encrypted or clear text. Proceed to the next step to replace an enable secret, console login, or enable password. If there is no enable secret password, note the enable and console login passwords, if they are not encrypted, and proceed to Step 17. Failure to follow the steps as shown might cause you to erase your router configuration. This action allows you to modify or replace passwords in the configuration. You can remove individual passwords by using the no form of the above commands. For example, entering the no enable secret command removes the enable secret password. If you omit this step, all interfaces are administratively shut down and unavailable when the router is restarted. If you skipped. This guide contains important The Cisco 7200 VXR routers include the Descriptions and examples of software commands are included when they are necessary for replacing, installing, configuring, or maintaining the router hardware. A Cisco 7200 VXR router equipped with an NSE-1 or NPE-400 can support up to six high-speed port adapters and can also support higher-speed port adapter interfaces including Gigabit Ethernet and OC-12 ATM.

Other interface commands might be needed, depending on the nature of the connected network. The show controller command is a very powerful debugging aid, especially for Cisco engineers should you need help in debugging a problem. If you have any problems with your Gigabit Ethernet interfaces, you will need to provide this information to Cisco for analysis. To configure the interface parameters, you need your interface network addresses and subnet mask information. Consult with your network administrator for this information. Follow these steps to configure an ATM interface. Enter yes to configure for extended AppleTalk networks, and then enter the cable range number. Enter the zone name and any other additional zones that are associated with your local zone: Follow these steps to configure Fast Ethernet interfaces. Enter yes to configure for extended AppleTalk networks, and then enter the cable range number. Enter the zone name and any other additional zones that are associated with your local zone: Follow these steps to configure synchronous serial interfaces: Enter yes to configure for extended AppleTalk networks, and then enter the cable range number. Enter the zone name and any other additional zones that are associated with your local zone: You can use the setup command if you want to modify the parameters after the initial configuration. To perform more complex configurations, use the configure command. Complete the following steps to configure the router manually: Press Ctrl-Z (hold down the Control key while you press Z ) or enter end to exit configuration mode and return to the EXEC command interpreter. To see a list of the configuration commands available to you, enter.If you fail to do this, your configuration will be lost the next time you reload the router. These publications contain additional information on using the configure command. The enable secret password is encrypted, however, and must be replaced with a new enable secret password.

Cisco 7200 VXR Installation and Configuration Guide 1-46 78-5469-03. This LED remains on during normal operation of the router. Cisco 7200 VXR Installation and Configuration Guide 1-48. See Chapter 3, “Installing a Cisco 7200 VXR Router,” the “Connecting to the Ethernet and Fast Ethernet Ports” section on page 3-21 for Fast Ethernet MII connection requirements. Port Adapters and Service Adapters The port adapters and service adapters installed in the Cisco 7200 VXR routers are of the same type as those installed on the second-generation Versatile. This configuration note accompanies every PA-4E port adapter that is shipped from the factory as an installed item in a Cisco 7200 VXR router or as a FRU. The configuration note is also available on the Documentation CD-ROM and on CCO. A second power supply, although not required, allows load sharing and increased system availability. A modular power cable connects the AC-input power supply to the site AC power source. Figure 1-4 shows a Cisco 7206VXR with an installed power supply filler plate. Table 1-1, earlier in this chapter, lists the AC-input and DC-input power supply system power specifications, including input voltage and operating frequency ranges. The subchassis assembly contains the midplane, the fan tray, two power supply bays, and one slot for the network processing engine. To avoid potential problems when you install spare Flash Disks or Note. The kit is shipped with each Cisco 7200 VXR router and is also available as a single FRU. For a description of the MAC-layer address, see the “MAC-Layer Address”. Using this address scheme, you can remove port adapters and insert them into other routers without causing the MAC addresses to move around the network or be assigned to multiple devices. When you remove or insert a port or service adapter in a Cisco 7200 VXR router, the midplane pins send signals to notify the system, which then performs as follows: Rapidly scans the midplane for configuration changes.

Table 1-1 lists the Cisco 7200 VXR physical specifications and power requirements.In addition, the Cisco 7204VXR midplane provides increased support for multiple high-bandwidth port adapters.Cisco 7200 VXR routers also support the NSE-1, which consists of two modular boards: the processor engine board and the network controller board. The NSE-1 Parallel eXpress Forwarding (PXF) processor works with the routing processor to provide accelerated packet switching, as well as accelerated IP Layer 3 feature processing. Cisco 7200 VXR Installation and Configuration Guide 1-16 78-5469-03. The network processing engines and network services engine perform the. Table 1-11 lists NSE-1 memory specifications, and Table 1-12 lists memory configurations. Figure 1-5 NPE-100 Midplane connectors Temperature sensor System DRAM SIMMs controller Bank 1 R4700 microprocessor Bank 0 Captive Temperature Handle sensor installation screw Cisco 7200 VXR Installation and Configuration Guide 1-18 78-5469-03. Cisco 7200 VXR Installation and Configuration Guide 1-21 78-5469-03. Cisco 7200 VXR Installation and Configuration Guide 1-22 78-5469-03. Cisco 7200 VXR Installation and Configuration Guide 1-24 78-5469-03. Socket U15 is never populated. Cisco 7200 VXR Installation and Configuration Guide 1-28 78-5469-03. Cisco 7200 VXR Installation and Configuration Guide. The SRAM component is made to act like the NVRAM by the addition of some external components, one of which is a 1-inch (2.54-cm) button-type lithium battery. Cisco 7200 VXR Installation and Configuration Guide 1-41 78-5469-03. These LEDs remain off during Slot 1 normal operation of the router. Cisco 7200 VXR Installation and Configuration Guide 1-42 78-5469-03. Cisco 7200 VXR Installation and Configuration Guide 1-43 78-5469-03. Cisco 7200 VXR Installation and Configuration Guide 1-45 78-5469-03. This LED remains off during normal operation of the router unless there is an incoming carrier signal.

, 170 West Tasman Drive, San Jose, CA 95134-1706 USA Cisco Router and Security Device Manager (SDM) User Guide for the Cisco 7200 VXR and Cisco 7301 Routers October, 2006 Note This User Guide covers the Cisco 7204VXR, the Cisco 7206VXR, and the Cisco 7301 routers. For information on additional SDM supported platforms, go to. Cisco Router and Security Device Manager (SDM) is an intuitive Java-based dev ice-management tool that lets you configure LAN interfaces, routing, Network Address Translation (N AT), firewalls, V irtual Private Networks (VPNs), and other features without knowledge of the Cisco command-line interface (CLI). Note SDM does not support the following features on the Ci sco 7200 VXR or Cisco 7301 routers: SDM Reset, WAN configuration; therefore, you will need to use CLI commands to support th ese functions. The SDM Express Wizard is not supported on the Cisco 7000 family. SDM is preinstalled on your router Flash Disk or CompactFlash Disk when yo u order a security bundle comprising a Cisco 7204VXR, Cisco 7206VXR, or Cisco 7301 router. SDM can also be purchased and installed on an existing Cisco 7204VXR, Cisco 7206VXR, or Cisco 7301 router. See “Installing SDM (Optional)” section on page 6 for instructions on downloading and installing SDM. Because SDM uses a GUI interface, it requires th at you access it from a PC using a supported web browser. For the supported browsers, see the “Cisco IOS Software Requirements” section on page 4. Dynagen simplifies building and working with virtualConfiguration file has a simple syntax forNo need to deal withDynagen can also controlEverything in this section isThis is the fully qualified path relative to theThis is the fully qualified path relative to theInclude a description here.This is optional, and if not done dynagen will make saneCan take the following forms:All keywords are optionalUbuntu and Canonical are registered trademarks of Canonical Ltd. We apologize for the inconvenience.

If you would like to know more or refuse all or some of the cookies, please click here. It only takes a minute to sign up. A manual BGP reset on this router resolves all of our problems. When you are able to login to the router, try a show log and see what it says over the past day or so, there will probably be some pointers in there. Although routers are, when it comes down to it, computers with specialized hardware they have completely different failure modes. Where is your primary DNS server, is it on this side of the router or the far side of the router? This can really mask many other problems that are usually fairly easy to solve. Name resolution - Only some sites fail to resolve. Primary DNS is on this side of the router. Router is doing NAT. Please be sure to answer the question. Provide details and share your research. Making statements based on opinion; back them up with references or personal experience. To learn more, see our tips on writing great answers. Browse other questions tagged cisco bgp or ask your own question. ClusterXL in Load Sharing mode supports up to 5 Cluster Members. Note - Configuring more than 4 members significantly decreases cluster performance due to amount of Delta Sync. Virtual System Load Sharing (VSLS) mode supports up to 13 Cluster Members. For example: Meaning that the same Software Blades and features must be enabled on all Cluster Members: Fail-over from a Cluster Member to a peer Cluster Member with a greater number of CoreXL Firewall instances keeps all connections. Fail-over from a Cluster Member to a peer Cluster Member with a smaller number of CoreXL Firewall instances interrupts some connections. The connections that are interrupted are those that pass through CoreXL Firewall instances that do not exist on the peer Cluster Member. In addition, Full Sync will fail. These devices and the Cluster Members must interact to assure network connectivity.

If an internal power supply temperature or voltage reaches a critical level, the power supply shuts down without any interaction with the system processor. Cisco 7200 VXR Installation and Configuration Guide 1-64 78-5469-03. You can also retrieve and display environmental status reports with the show environment, show environment all, show environment last, and show environment table commands. The show environment all command also displays a report showing which power supply slots are occupied and which are empty. Cisco 7200 VXR Installation and Configuration Guide 1-68 78-5469-03. Cisco 7200 VXR Installation and Configuration Guide 1-69 78-5469-03. We have 9 Cisco 7200 VXR Series manuals available for free PDF download: Installation And Configuration Manual, Configuration Manual, User Manual, Product Overview, Quick Start Manual, Manual, Datasheet Make Sure to Review the Safety Warnings Listed in the Publication. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0711R) Prev. Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up there. Please also check your spam folder. As a result, the web page can not be displayed. Cloudflare monitors for these errors and automatically investigates the cause. To help support the investigation, you can pull the corresponding error log from your web server and submit it our support team. Please include the Ray ID (which is at the bottom of this error page). Additional troubleshooting resources. Sending 5, 100-byte ICMP Echos to 20.20.20.1, timeout is 2 seconds. Packet sent with a source address of 10.10.10.1Session status: UP-ACTIVE. Peer: 1.1.1.2 port 500. Descriptions and examples of software commands are included when they are necessary for replacing, installing, configuring, or maintaining the router hardware.

The NPE-G2 provides high-speed performance with the Motorola Freescale 7448 1.67-GHz processor and supports three Gigabit Ethernet interfaces with no additional bandwidth requirements. The NPE-G2 also provides a dedicated Fast Ethernet Management port and two USB ports for data storage and seCaution To ensure the proper flow of cooling air across the internal components, make sure blank port adapters are installed in unoccupied port adapter slots, and power supply filler plates are installeCaution To ensure tReplacement instructions are available on theTable 1-2 NPE-G2See Figure 1-7. Table 1-7 NSE-1 SDRAM DIMM Memory Con?gurations Total SDRAM SDRAM Bank Quantity Product Number 1Table 1-8 NPE-400 Memory Speci?cations Memory Type Size Quantity Description Location SDRAM-configurable 128, 256, or 1 128-, 256-, or 512-MB J1 512 MB SODIMM 1 Boot ROM 512 KB 1 OTP ROM for the ROM U7 monitor program Primary cache 16 KB — RM7000 processor, U38 (instruction), integrated ca. List is read-only.Applies to CDP. Can be used to connect with mac-telnet. Applies only to devices installed with RouterOS. Shown only to devices installed with RouterOS. If it does, it will send out basic information about system and process received discovery packets broadcasted in Layer-2 network. List of interfaces is automatically managed by RouterOS. Items in the list cannot be removed nor added. Default settings depend on interface type and current state.Whenever master interface (e.g. bonding or bridge) is included in the discovery interface list, all its slave interfaces will automatically participate in neighbor discovery. It is possible to allow neighbor discovery only to some slave interfaces. To do that, include the particular slave interface in the list and make sure that the master interface is not included. Cisco Systems, Inc.

This section outlines the requirements imposed by ClusterXL on surrounding networking equipment. To let the CCP packets pass between Cluster Members, configure the settings below on the surrounding switches. You can disable IGMP registration on Cluster Members. To let the traffic reach the cluster, configure the settings below on the surrounding routers. To let the traffic reach the cluster, the router must support sending unicast IP packets with multicast MAC addresses. If you have a router that is not able to learn this type of mapping dynamically, you need to configure static MAC entries to map unicast Cluster Virtual IP addresses to multicast MAC addresses. This may cause a multicast storm through the network. Disable such configuration on your router. In a High Availability environment, the single member is the Active member. In a Load Sharing Unicast environment, the single member is the Pivot. The G-ARP packets associate the Virtual IP address of the cluster with the physical MAC address of the new Active member (or Pivot member). When this happens: Switches continue to send traffic to the physical MAC address of the member that failed. This results in traffic outage until the switches have fully updated ARP cache tables. In Virtual MAC mode, the VMAC that is advertised by the cluster members (through Gratuitous ARP Requests) keeps the real MAC address of each member and adds a Virtual MAC address on top of it. See sk50840. Go to the ClusterXL and VRRP page. In the Select the cluster mode and configuration section, select High Availability and select ClusterXL. In the Advanced Settings section, select Use Virtual MAC. Click OK. Install a Policy on this cluster object. To configure VMAC Mode on the command line: Log in to Expert mode.Run: cphaprob -a if For more details, or instructions for other networking devices, always refer to the device vendor documentation. For example: 01:00:5e:00:00:fa for the 10.0.0.

X network To add a permanent CAM entry for the multicast MAC address for module 1 - port 1, and module 2 - ports 1, 3, and 8 through 12: Define a static CAM entry (entry will remain in the CAM table until the switch is reset).Define a static ARP entry. Please enable JavaScript and reload the page. The following displays the IOS configuration related to the CA: Note that you must omit the pkiclient.exe filename at the end which is automatically add by IOS. If you see this you have enrolled successfully: The following describes how to configure and enroll directly with EJBCA using GNS3 on Ubuntu 8.10: Also configure a simple topology: If you have any ideas, please contact us. We are a non-profit group that run this service to share documents. We need your help to maintenance and improve this website. Pr ovides highe st DRAM memor y with optional up grade to 1 Gigaby te DRAM comp ared to NPE-400 with 512 Megaby te DR AM 8. Protects your inve stment by continuing to use existing por t and ser vic e adapters and power supplie s 9. Supp or t s la te st f eatures through newer Cisc o IOS release s that ar e supp orte d on 7200V XR and NPE-G 1 and ex tends the life suppor t by replacing non- V XR chassis and older Net work Proce ssing Engines (NPEs) that are End-of-Lif e or approaching End-of -Lif e Cis c o 7200V XR S erie s and Net work Pr o c e s sing Engine NPE- G 1 Up grade Quick Look Ne tworks continue to evolve t o me e t the requirements o f new applica tions, while maintaining the se curit y o f critical inf ormation and r e source s. The Cisco 7200 S eries, with the high per formance network proce ssing engine NPE-G 1 provides the p er f ormanc e and flexibility t o meet thes e ne t w ork requirements. Cust omers who currently ha ve a 7200VXR chassis can drama tically increase network per formance and preser ve their investment in chassis and line car ds by upgrading to the NPE -G 1.

Cust omers with non- VXR chassis can up grade t o a new 7200VXR chassis plus NPE-G 1 using a t tr active trade-in cr edits. At the same time, customers can re-use their exis ting interface cards.Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Cisco 7206VXR owners to properly answer your question. Ask a question About the Cisco 7206VXR This manual comes under the category Routers and has been rated by 1 people with an average of a 5.7. This manual is available in the following languages: English. Do you have a question about the Cisco 7206VXR or do you need help. Ask your question here Cisco 7206VXR specifications Brand A router then distributes the Internet signal to the devices connected to the router.This radiation cannot damage cells and tissues and is therefore not harmful to human health.ManualSearcher.com ensures that you will find the manual you are looking for in no time. Our database contains more than 1 million PDF manuals from more than 10,000 brands. Every day we add the latest manuals so that you will always find the product you are looking for. It's very simple: just type the brand name and the type of product in the search bar and you can instantly view the manual of your choice online for free. ManualSearcher. com If you continue to use this site we will assume that you are happy with it. Read more Ok. Keeping the handset in the cradle will prevent misdialing the telephone number or accidentally dialing 911. Verify the telephone number you have dialed by checking the LCD screen. Press Dial or pick up the handset to complete the telephone call. To disengage mute, press Mute again or lift the handset. Remember, you do not need to dial 9 for a school to school call. Verify the number you have dialed by checking the LCD screen, press Dial or pick up the handset to place the call.

Verify the number you have dialed by checking the LCD screen, press Dial or pick up the handset to place the call. Remember to keep the handset in the cradle to avoid misdialing the number or accidentally dialing 911. Verify the number you have dialed by checking the LCD screen, press Dial or pick up the handset to place the call.You will hear two beeps. 2. Enter the extension to which you want to forward all of your calls. Enter the number exactly as you would if you were placing a call to that extension.Then dial the selected extension and wait for the person to answer, once the desired party answers and wants to accept the call, press the Transfer soft key to hand the call over to the desired party. Place the call on park, the call park number will appear on LCD screen; i.e. 800-810. Now that the call is parked it can be picked-up by any IP telephone in the school just by dialing the parked number. The play button may be used to preview ring tone, once the ring tone is selected choose ok and exit. If configuring voice mail for the first time you will be asked to enter your PIN, which is 1234. Follow the voice directions to listen, save, erase, and forward calls. From here you will able to download the Cisco 7200 series IOS for GNS3. If you have the choice, I recommend to use Qemu nodes instead of VirtulaBox for the following reasons: GNS3 offers multiple ways to emulate IOS. For older images, we use and maintain Dynamips; an emulator dedicated to emulate some Cisco hardware. Dynamips can run unmodified IOS images.We were told it is possible, but I am not able to find an IOS image with PPPoE support. Any pointers are welcome. TIA NaNa Cisco 7200 7200VXR Routers IOS Software. For the following routers: Cisco 7206 Router Cisco 7206VXR Router Cisco 7204 Router Cisco 7204VXR Router Cisco 7202 Router Cisco 7201 Router.Now I have vlan ID 2402.I have done it many times!

According to a Network World, Wachovia Bank uses over 400 Cisco 7200 Series Routers to maximize network performance (WAN) for VOIP across hundreds of branch offices nationwide. Searched for MIB: CISCO-DEVICE-LOCATION-MIB How I can install IOS into cisco switch 3560 series.We help companies of all sizes transform how people connect, communicate, and collaborate. With double the performance for multiple services from previous generations and full Cisco IOS(R) Software feature support, the Cisco 7200 NPE-G2 has the highest performance and scalability within the family of network processing engines. Its always better to use 12.4 IOS as they provide full command support.. CBT Nuggets - Cisco CCNA ICND2 200-101 Video Direct Download Download 01 - Welcome To Icnd2 - Cisco Certification And Getting The Most Fro. CBT Nuggets - Cisco. Customers with active service contracts will continue to receive support from the Cisco Technical Assistance Center (TAC) until November 16, 2011. Idle PC is used to map the idle instruction of the running IOS to the idle instruction of the. There are several additional Cisco IOS images below. WAN, Routing and Switching Page 3 Cisco IOS Release 12.0(5)S or later releases of 12.0 S Cisco IOS Release 12.0(3)T or later releases of 12.0 T Cisco IOS Release 12.2(1) or later releases of 12.2 Cisco IOS Release 12.2 (4)B or later releases of 12.2 B( Compliance CE Marking. In addition, Cisco 12000 Series (GSR) routers running Cisco IOS Software have a second vulnerability related to a crafted multicast packet. Participate in live expert events and join the ongoing technical support forum in our communities. We have 9 Cisco 7200 VXR Series manuals available for free PDF download: Installation And Configuration Manual, Configuration Manual, User Manual, Product Overview, Quick Start Manual, Manual, Datasheet. Pr ovides highe st DRAM memor y with optional up grade to 1 Gigaby te DRAM comp ared to NPE-400 with 512 Megaby te DR AM 8.

cisco 7246 manual

Configuration Examples for Extended Upstream Frequency RangesPagina 17 Support for Extended Upstream Frequency RangesConfiguration Examples for Extended Upstream Frequency RangesPagina 20 Support for Extended Upstream Frequency RangesAdditional ReferencesPagina 21 Support for Extended Upstream Frequency RangesMIBs. MIBs MIBs Link. Pagina 22 Support for Extended Upstream Frequency RangesCommand ReferencePagina 23 Support for Extended Upstream Frequency RangesPagina 24 Support for Extended Upstream Frequency RangesPagina 25 Support for Extended Upstream Frequency RangesPagina 27 Support for Extended Upstream Frequency RangesPagina 28 Support for Extended Upstream Frequency Ranges. No accounts or sign ups necessary!While you are waiting, you will have the opportunity toThe time required is typically tied to the size of the manual. Productivity Tools supports integrations with other applications, such as Microsoft Office (Word, Excel, and PowerPoint), Microsoft Skype for Business, Microsoft Lync, Internet Explorer, and IBM Lotus Notes. For information on the desktop app, see Cisco Webex Meetings Desktop App Yes, thank you! Not really What was great. Where did we go wrong. I don't like how the product works I found the instructions or explanations in the article confusing This article didn't answer my questions or solve my problems Other Submit article feedback Thanks for your feedback. All rights reserved. This document is Cisco public. Established in 1984, the company is now associated with world-class quality network products that offers easy business set-up with security. Their routers range from basic-entry level devicees for small business connectivity to carrier routers that can be used by ISPs in delivering content to their subscribers. Read about the easy steps you can take to configure the router properly. Read More.

• cisco 7246 manual, cisco 7206 manual, cisco 7246 manual pdf, cisco 7246 manual download, cisco 7246 manual instructions, cisco 7246 manual free.

We have 4 Cisco 7246 - uBR Router manuals available for free PDF download: Hardware Installation Manual, Supplementary Manual, Configuring, User Manual. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Support for Extended Upstream Frequency Ranges Cisco IOS Release 12.2(15)BC2 adds support for the extended upstream frequency range that is used in cable networks in Japan and other areas. This feature also clarifies the configuration of DOCSIS and EuroDOCSIS networks, so that the router shows only those upstream and downstream frequencies that are valid for each mode of operation. Feature History for Extended Upstream Frequency Ranges Finding Support Information for Platforms and Cisco IOS Software Images Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image support. Access Cisco Feature Navigator at Pagina 2 Support for Extended Upstream Frequency RangesPrerequisites for Extended Upstream Frequency RangesInformation About Extended Upstream Frequency RangesPagina 5 Support for Extended Upstream Frequency RangesPrerequisitesPagina 6 Support for Extended Upstream Frequency RangesStep 4. Pagina 7 Support for Extended Upstream Frequency RangesPagina 8 Support for Extended Upstream Frequency RangesStep 4. Pagina 9 Support for Extended Upstream Frequency RangesPagina 10 Support for Extended Upstream Frequency RangesStep 6. Pagina 11 Support for Extended Upstream Frequency RangesPagina 12 Support for Extended Upstream Frequency Ranges. Configuration Examples for Extended Upstream Frequency RangesEuropean (EuroDOCSIS) Frequency Range Configuration Example. Pagina 14 Support for Extended Upstream Frequency Ranges.

For additional information on configuring the Cisco uBR7246 universal broadband router, the following documentation resources are available: The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly; therefore, it might be more up to date than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at,, or Click Feedback on the toolbar, and then select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.You can access Cisco IOS software configuration documentation on the World Wide Web at,, or Customer Service hours are 5:00 a.m. to 6:00 p.m. Pacific time, Monday through Friday (excluding company holidays).You must boot and log in to the router before you can enter an EXEC command. For security purposes the EXEC has two levels of access to commands, user EXEC mode and privileged EXEC mode. Because many privileged-level EXEC commands are used to set operating parameters, you should password-protect these commands to prevent unauthorized use. The passwords should be different for maximum security. If you enter the same password for both during the setup script, the system will accept it, but you will receive a warning message indicating that you should enter a different password. In both cases, a number cannot be the first character. Leading spaces are ignored, trailing spaces are recognized, and alphanumeric characters are recognized as uppercase or lowercase. The show version command displays the release of Cisco IOS software that is available on the router. If the remote end of the WAN connection is connected and properly configured, the AutoInstall process begins. Perform the following step to complete this task.

Benefit from SOC2 audited controls, proactive management, monitoring, security and backups in both multi-tenant or single-tenant variations with hybrid cloud integration. Learn More Managed Public Cloud AWS or Azure are powerful cloud platforms, but it can be complicated. If you're thinking about moving to public cloud or looking to offload managing your public cloud deployment, we can manage, secure and optimize your cloud so you can focus on key business goals. From first click, to failover, we are there every step of the way.Our customers trust us to manage, protect and optimize their critical cloud infrastructure because of our obsession with solving complex problems. We know that customers want to be treated like a big fish in a small pond and we have the DNA to tailor our services to meet your needs. We have been impressed with their services and look forward to expanding our partnership in the future. The heavy lifting of building out our infrastructure according to our design belongs to the experts at Carbon60. That is something we seriously value. Technically solid, highly available and refreshingly pro-active, they were a truly committed partner. Each interaction is handled with care, knowledge, efficiency and outstanding communication skills. A glitch on our application impacted site performance and I appreciate how fast your team fixed the problem last night. That is why I moved to Carbon60. Exceptional service. You get a gold star! We take care of management, security, DevOps automation and optimization of your AWS infra while you focus on your apps. The chapter contains the following sections: The effective use of these features is easier if you have more information at hand.

In this example, an MC11 cable modem card is installed in cable modem card slot 3. The setup program will determine the status of all interfaces. For all inactive ports, the default will be no. You can press Return to accept the default. To configure the interface parameters, you need your interface network addresses and subnet mask information. Consult with your network administrator for this information. Respond to the prompts as follows, using your own addresses and mask at the setup prompts: Complete the following steps to configure the serial ports: These parameters are shown in the order in which they appear on your console terminal. Only one Ethernet and one synchronous serial interface are configured for this example. The following configuration command script was created:Use the enabled mode 'configure' command to modify this configuration. Press RETURN to get started! You can use the setup command if you want to modify the parameters after the initial configuration. To perform more complex configurations, use the configure command. Complete the following steps to configure the Cisco uBR7246 manually: Press Ctrl-Z to exit configuration mode. To see a list of the configuration commands available to you, enter.If you fail to do this, your configuration will be lost the next time you reload the router. These publications contain additional information on using the configure command. For example, if a Fast Ethernet port adapter is installed, refer the configuration note PA-FE-TX and PA-FE-FX 100BASE-T Fast Ethernet Port Adapter Installation and Configuration (Document Number 78-2659-xx). This configuration note accompanies every Fast Ethernet port adapter that is shipped from the factory as an installed item in a Cisco uBR7246 or as a FRU. The document is also available on the Cisco Connection Documentation CD-ROM and on Cisco Connection Online (CCO).

If you fail to do this, your configuration will be lost the next time you reload the router. If the LAN or WAN cable is not connected, the router will boot from Flash memory and go into the setup facility automatically. These parameters are used for controlling system-wide settings. Complete the following steps to enter the global parameters: When you see this information, you have successfully booted your router: Rights clause at FAR sec. 52.227-19 and subparagraphSoftware clause at DFARS sec. 252.227-7013.Copyright (c) 1986-1998 by cisco Systems, Inc. Compiled Sun 21-Dec-97 04:10 by asdhkj. R4700 processor, Implementation 33, Revision 1.0 (Level 2 Cache). Last reset from power-on. Bridging software. SuperLAT software copyright 1990 by Meridian Technology Corp). X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. TN3270 Emulation software (copyright 1994 by TGV Inc).Configuration register is 0x0On subsequent uses of the setup command facility, the script begins with a System Configuration Dialog as shown in the following example.For Internet Protocol (IP)-only installations, you can accept the default values for most of the questions. A typical configuration using IP follows and continues through Step 7: It provides a means to access and set configuration and run-time parameters of routers and communication servers. SNMP defines a set of functions that can be used to monitor and control network elements. When you are using IP routing, you must also select an interior routing protocol. You can specify only one of two interior routing protocols to operate on your system using setup: In terior Gateway Routing Protocol (IGRP) or Routin g Information Protocol (RIP). In this example, an 8-port Ethernet port adapter is installed in port adapter slot 1. The setup program will determine the status of all interfaces. For all inactive ports, the default will be no. You can press Return to accept the default.

The power supply contains a main power switch, OK LED, and either an AC-input power receptacle, orAdjacent to the lower power supply bay, two M5 chassis grounding receptaclesCisco uBR7200 Series Universal Broadband Router AC Power Supply Replacement InstructionsThe Cisco uBR7246VXR and Cisco uBR7246 support an optional, second power supply for load sharingIf you purchased a Cisco uBR7246VXR or Cisco uBR7246 and you want toA handle on the AC-input power supply unit provides a grip point for removing and replacing the powerTwo captive installation screws secure the power supply to the chassis and seat the power supply in theThe AC-input power supply has a receptacle for an AC-input power cable. A modular power cableA cable-retention clip secures theNote. Each AC-input power supply has an electrical current rating of 7A. Figure 2. Cisco uBR7246 and Cisco uBR7246VXR AC-Input Power Supply. Cable-retention clipAC-input receptacle. Caution. Power switch. Handle. When the input power to Cisco uBR7246 universal broadband router power supply is disconnected orWait at least 10 seconds or move the powerFor example, if the power supply wasInstallation Prerequisites. This section provides a list of parts and tools you need to remove and replace the AC-input power supplyThis section also includes safety and ESD-prevention guidelines toCisco uBR7200 Series Universal Broadband Router AC Power Supply Replacement InstructionsParts and Tools. You need the following tools and parts to remove and replace the AC-input power supply in the. Cisco uBR7200 series. If you need additional equipment, contact a service representative for orderingAn AC-input power supply. Number 2 Phillips screwdriver. Several cable ties (if the router is mounted in an equipment rack). Safety Guidelines. Following are safety guidelines that you should follow when working with any equipment that connectsSafety Warnings.

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, mightWarning Definition. WarningYou are in a situation that could cause bodily injury. BeforeUse the statement number provided atStatement 1071Follow these basic guidelines when working with any electrical equipment. Before beginning any procedures requiring access to the chassis interior, locate the emergencyDisconnect all power and external cables before moving a chassis. Do not work alone if potentially hazardous conditions exist. Never assume that power has been disconnected from a circuit; always check. Do not perform any action that creates a potential hazard to people or makes the equipment unsafe. Carefully examine your work area for possible hazards such as moist floors, ungrounded powerCisco uBR7200 Series Universal Broadband Router AC Power Supply Replacement InstructionsTelephone Wiring Guidelines. Use the following guidelines when working with any equipment that is connected to telephone wiring orNever install telephone wiring during a lightning storm. Never install telephone jacks in wet locations unless the jack is specifically designed for wetNever touch uninsulated telephone wires or terminals unless the telephone line has beenUse caution when installing or modifying telephone lines. Preventing Electrostatic Discharge Damage. Electrostatic discharge (ESD) damages equipment and impairs electrical circuitry. ESD occurs whenElectromagnetic interference (EMI) shielding, connectors,Although the metal carrier helps to protect the printed circuit boards from ESD, wear a preventiveIf no wrist strap is available, groundCaution. Make sure to tighten the captive installation screws on the network processing engine, cable modem. These screws prevent accidentalFollowing are guidelines for preventing ESD damage. CautionEnsure that the ESD strap makes contact with your skin.Periodically check the resistance value of the antistatic strap.

This configuration note will accompany every Cisco MC11 cable modem card that is shipped from the factory as an installed item in a Cisco uBR7246 or as a FRU. The document is also available on the Cisco Connection Documentation CD-ROM and on Cisco Connection Online (CCO). Page Count: 16 Router AC Power Supply Replacement. Instructions. This document explains how to remove and replace the AC-input power supply in the Cisco uBR7200It includes instructions for powering down the routers, removing an installedThis document also includes steps for verifying theNote. Use this document in conjunction with the Cisco uBR7200 Series Universal Broadband Router. Hardware Installation Guide, Cisco uBR7200 Series Universal Broadband Router Software. Configuration Guide, and Regulatory Compliance and Safety Information for the Cisco uBR7200 Series. Universal Broadband Router. The following sections are included in this document. If You Need More Information, page 2. AC-Input Power Supply Overview, page 2. Installation Prerequisites, page 4. Removing and Replacing an AC-Input Power Supply, page 7. Obtaining Documentation and Submitting a Service Request, page 16. Americas Headquarters. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USAIf You Need More Information. The Cisco IOS software running on your router contains extensive features and functionality. ForNote. For Cisco IOS software configuration information, refer to the modular configuration and modularYou can access Cisco IOS software configuration documentation at Cisco.com. For hardware installation and maintenance information on the Cisco uBR7200 series, refer to the. Cisco uBR7200 Series Universal Broadband Router guides. For international agency compliance, safety, and statutory information for wide-area networkInformation for the Cisco uBR7200 Series Universal Broadband Routers that is shipped with your. Cisco uBR7200 series universal broadband router.

To obtain general information about documentation, refer to the “Obtaining Documentation and. Submitting a Service Request” section on page 16. AC-Input Power Supply Overview. The Cisco uBR7225VXR router is equipped with one of the following power supplies:The maximum AC-input power with single or dual power supply configuration is 300W. TheThe maximum AC-input power with single or dual power supply configuration is less than 700W. The minimum IOS release supported on this power supply is the Cisco IOS Release 12.2(33)SCD. Note. Ensure that you do not use a combination of these power supplies in the uBR7225VXR router.To ensure adequate airflow across the Cisco uBR7225VXR, Cisco uBR7246VXR, and Cisco uBR7246Do not mix AC-input and DC-input power supplies in the same Cisco uBR7246VXR or Cisco uBR7246Cisco uBR7200 Series Universal Broadband Router AC Power Supply Replacement InstructionsCisco uBR7225VXR. Each power supply contains a main power switch, the OK LED, and the AC-input power receptacle. TheThe Cisco uBR7225VXR supports an optional, second power supply for load sharing and powerNote. The Cisco uBR7225VXR router supports the 300W and the 540W AC-input power supplies. Ensure thatA handle on the AC-input power supply unit provides a grip point for removing and replacing the powerA single captive installation screw secures the power supply to the chassis and seats the power supply inNote. For the Cisco uBR7225VXR, the 300W AC-input power supply has an electrical current rating of 4AThe Cisco uBR7225VXR power supply device does not have a cable retention clip. Figure 1. Cisco uBR7225VXR AC-Input Power SupplyWhen this occurs, oneThe Cisco uBR7225VXR power supply mustCisco uBR7246 and Cisco uBR7246VXR.

The measurement should be within theCisco uBR7200 Series Universal Broadband Router AC Power Supply Replacement InstructionsEnsuring Easy Access to the Router. If your Cisco uBR7200 series router is installed in a standard 19-inch-wide, four-post equipment rack orUse the following guidelines to ensure easy access to the rear of the router when it is installed in a rack. Ensure that you have at least three to four feet of working space at the rear of the router. If cables from other equipment in the rack fall in front of the rear end of the router, carefully gatherIf access to the rear of the router is partially blocked by a power strip or some other permanent rackMake sure that at least one other person is available to support the front of the router as you slide it outRemoving and Replacing an AC-Input Power Supply. The following sections explain how to remove and replace an AC-input power supply in a. Cisco uBR7200 series router for a single power supply configuration and a dual power supplyCaution. When the input power to a Cisco uBR7200 series power supply is disconnected or lost, the power supplyWait at least 90 seconds or move the power switch from oneFor example, if the power supply was ON when theIf you do not wait the full 90 seconds or move the power switch from one position to the other, the powerThis caution note does not apply to the Cisco uBR7225VXR power supply. Single Power Supply Configuration. Removing and replacing the AC-input power supply in a single power supply configuration involves thePowering Down the Router, page 8. Disconnecting AC-Input Power, page 8. Removing the AC-Input Power Supply, page 9. Installing the AC-Input Power Supply, page 10. Cisco uBR7200 Series Universal Broadband Router AC Power Supply Replacement InstructionsReconnecting AC-Input Power, page 11. Powering Up the Router, page 12. These tasks are described in detail in the following subsections. Powering Down the Router.

Before powering down the router, use the copy running-config startup-config command to save theStep 1. Facing the rear of the router, place the power switch (on the power supply) in the OFF (O) position. Repeat this action if a second power supply is installed in the router. Step 2. Observe the following items. The green OK LED on the power supply goes off. The fans stop operating. The LEDs on the port adapters go off. The LEDs on the cable modem cards go off. This completes the procedure for powering down the router. Proceed to the following sectionDisconnecting AC-Input Power. Warning. Do not touch the power supply when the power cord is connected. For systems with a powerFor systems without a power switch, line voltages are present withinWarning. Before working on equipment that is connected to power lines, remove jewelry (including rings,Metal objects will heat up when connected to power and ground and canStep 1. Unplug the input power cable from the power source. Push the cable-retention clip that secures the input power cable to the router power supply to the left. Step 3. Unplug the other end of the input power cable from the power supply. (See Figure 3.). The Cisco uBR7225VXR power supply devices do not have a cable retention clip. Cisco uBR7200 Series Universal Broadband Router AC Power Supply Replacement InstructionsFigure 3. Disconnecting Power from a Cisco uBR7200 Series AC-Input Power Supply. Cable-retention clip. PowerPowerCaptiveAC power cableThis completes the procedure for disconnecting AC-input power. Proceed to the following section,Removing the AC-Input Power Supply. Step 1. Using a number 2 Phillips screwdriver, loosen the two captive installation screws on the faceplate of theNote. If you are removing a power supply filler plate in preparation to install a second power supply, make sureIf the router is not installed in a standard four-post or telco rack, skip to Step 5. If the router is installedFigure 4.

Captive Installation Screws and Handle on the AC-Input Power Supply. Captive installation screwStep 2Cisco uBR7200 Series Universal Broadband Router AC Power Supply Replacement InstructionsStep 3. Position at least one person in front of the rack to support the front underside of the router. Step 4. From the rear of the rack, carefully push the front of the router out of the rack until there is enoughStep 5. Grasp the power supply handle and pull the AC-input power supply from the router. To maintain agency compliance requirements and meet EMI emissions standards for the. Cisco uBR7246VXR and Cisco uBR7246 with a single power supply, the power supply filler plate andThis completes the procedure for removing the AC-input power supply from a Cisco uBR7200 seriesInstalling the AC-Input Power Supply. Make sure the power switch on the power supply is in the OFF (O) position. If you are adding a second power supply to a Cisco uBR7246VXR or Cisco uBR7246 that previouslyStep 2. Grasp the power supply handle with one hand and place your other hand underneath the power supplyFigure 5. Holding the AC-Input Power Supply. ConnectorStep 3. Align the power supply to the power supply bay. Cisco uBR7200 Series Universal Broadband Router AC Power Supply Replacement InstructionsStep 4. Slide the power supply completely in to the power supply bay until its faceplate is flush with the routerCaution. When inserting a power supply into the router, do not use unnecessary force; slamming the power supplyStep 5. Seat the power supply in the router by tightening the captive installation screws with a number 2 PhillipsNote. The power supply is not fully seated in the router midplane until you tighten the captive installationStep 6. If there is no second power supply, replace the filler plate and its attached air dam on the empty powerStep 7. If you pushed the router from the rack, slowly guide the router back into the rack. Step 8Caution.

Cisco uBR7246VXR and Cisco uBR7246 with a single power supply, the power supply filler plate andThis completes the procedures for installing the AC-input power supply in the router. Proceed to theReconnecting AC-Input Power. Never defeat the ground conductor or operate the equipment in the absence of a suitably installedStep 1. At the rear of the router, check that the power switch on the power supply is in the OFF (O) position. Push the cable-retention clip to the left, away from the AC receptacle, and plug in the power cable. Secure the cable in the power supply AC receptacle by pushing the cable-retention clip to the right untilThe cable-retention clip provides strain relief for the AC power cable. (See. Figure 6.). Cisco uBR7200 Series Universal Broadband Router AC Power Supply Replacement InstructionsFigure 6. Connecting AC-Input Power to a Cisco uBR7200 Series Router. Power receptacle. Captive installation screw. AC power cable. NotePlug the AC power supply cable into the AC power source. Each Cisco uBR7246 AC-input power supply has an electrical current rating of 7A. For the CiscoAC-input power supply has an electrical current rating of 6.5A. This completes the steps for reconnecting AC-input power to a Cisco uBR7200 series router. Proceed toPowering Up the Router. Check for the following. Each port adapter is inserted in its slot, and the port adapter retention clip is in the lockedNote. Cisco uBR7225VXR power supply devices do not have a cable retention clip. Each cable modem card is inserted in its slot, and its respective captive installation screws areAll network interface cables are connected to the port adapters. A Flash memory card is installed in its PCMCIA slot (if present). Each AC-input power cable is connected and secured with the cable-retention clip. The console terminal is turned on. Repeat thisThe green OK LED on the power supply goes on. Listen for the fans; you should immediately hear them operating.

During the boot process, observe the system LEDs. The LEDs on most of the port adapters and cableSome might go on, go out, and go on again for a short time. On. Step 5. Observe the initialization process. When the system boot is complete (after a few seconds), the network. During this initialization,The enabled LED on each portCisco Internetwork Operating System Software. Copyright (c) 1986-1998 by cisco Systems, Inc. Compiled Sun 09-Mar-98 04:10 by smith. This completes the procedures for powering up the router. This also completes the procedure forIf you have questions or need assistance, see the “Obtaining Documentation and Submitting a Service. Request” section on page 16. Otherwise, if your Cisco uBR7246VXR or Cisco uBR7246 has a dualCisco uBR7200 Series Routers.”. Dual Power Supply Configuration in the Cisco uBR7200 Series Routers. Removing and replacing an AC-input power supply in a dual power supply configuration in the or CiscoTurning OFF the Power Supply, page 13. Disconnecting AC-Input Power, page 14. Removing the AC-Input Power Supply, page 14. Installing the AC-Input Power Supply, page 14. Reconnecting AC-Input Power, page 11. Turning ON the Power Supply, page 16. Turning OFF the Power Supply. The second power supply maintains full system power (the system continues to operate asThis completes the procedure for turning off the power supply. Proceed to the following sectionCisco uBR7200 Series Universal Broadband Router AC Power Supply Replacement InstructionsDisconnecting AC-Input Power. Unplug the other end of the input power cable from the power supply. This completes the procedure for disconnecting AC input power. Using a number 2 Phillips screwdriver, loosen the two captive installation screws on the faceplate of theIf the router is not installed in a standard four-post or telco rack, skip to Step 5. If the router is installedStep 2Step 3. This completes the procedure for removing the AC-input power supply.

cisco 7301 manual

However, it is wise to shut down the interface before removing a port adapter that has active traffic moving through it. Removing a port adapter while traffic is flowing through the ports can cause system disruption. Once the port adapter is inserted, the ports can be brought back up. OIR is a method that is seamless to end users on the network, maintains all routing information, and preserves sessions. The connector has a set of tiered pins in three lengths that send specific signals to the system as they make contact with the port adapter or service adapter. The system assesses the signals it receives and the order in which it receives them to determine if a port adapter or service adapter is being removed or inserted into the system. From these signals, the system determines whether to reinitialize a new interface or shut down a removed interface. The system recognizes the signals and the sequence in which it receives them. Any newly inserted interface is put in the administratively shutdown state, as if it was present (but not configured) at boot time. If a similar port adapter type is reinserted into a slot, its ports are configured and brought online up to the port count of the original port adapter. (A service adapter has no configurable ports.) The environmental monitoring functions constantly monitor the internal chassis air temperature and DC supply voltages and currents. If conditions reach shutdown thresholds, the system shuts down to avoid equipment damage from excessive heat. The reporting functions periodically log the values of measured parameters so that you can retrieve them for analysis later, and the reporting functions display warnings on the console if any of the monitored parameters exceed defined thresholds. If the air temperature exceeds a defined threshold, the system controller displays warning messages on the console terminal, and if the temperature exceeds the shutdown threshold, the system controller shuts down the system.

• cisco 7301 manual, cisco 7301 manual, cisco 7301 manual pdf, cisco 7301 manual download, cisco 7301 manual free, cisco 7301 manual instructions.

The chapter contains the following sections: Complex configuration procedures are beyond the scope of this publication and can be found in the modular configuration and modular command reference publications in the Cisco IOS software configuration documentation set that corresponds to the software release installed on your Cisco hardware. It describes the numbering and addressing scheme of the port adapter for the router, the environmental monitoring and reporting functions, and online insertion and removal (OIR). These descriptions help you become familiar with the capabilities of the Cisco 7301 router. These addresses are not used by other devices in the network; they are specific and unique to each port. The Cisco 7301 router uses a specific method to assign and control the MAC addresses of its port adapters.To display information about all port adapter slots, use the show interfaces command. If you abbreviate the command ( sh int ) and do not specify port adapter type and slot number (or arguments), the system interprets the command as show interfaces and displays the status of all port adapters and ports. If the new port adapter matches the port adapter you removed, the system immediately brings it online. In order to enable OIR, an address allocator with unique MAC addresses is stored in an EEPROM on the system board. Each address is reserved for a specific port and slot in the router regardless of whether a port adapter resides in that slot. The MAC address for the port adapter slot in the Cisco 7301 is slot 0. You can remove a port adapter and insert it into another router without causing the MAC addresses to move around the network or be assigned to multiple devices. Also, each time a port adapter was replaced, other devices on the network would have to update their data structures with the new address. If the other devices did not update quickly enough, the same MAC address could appear in more than one device at the same time.

During this initialization, the LEDs on the port adapter probably will flash on and off. Systems, Inc.On the console terminal, after the system displays the system banner and hardware configuration, you will see the following System Configuration Dialog prompt: You do not have to configure the interfaces immediately; however, you cannot enable the interfaces or connect them to any networks until you have configured them. To verify correct operation of each interface, complete the first-time startup procedures and configuration, and then refer to the configuration note for the port adapter for LED descriptions and to check the status of the interfaces. You can configure features such as Access Control Lists (ACLs), routing protocols, and other options using the advanced mode SDM. SDM does not support the following features: WAN configuration, Gigabit Ethernet (GE) interfaces, AA client, EZ VPN server, QoS, SSHv2, DHCP server configuration options, and usability enhancements. If your router did not ship with SDM preinstalled, you can download a free copy from the Software Center at Cisco.com at. Because SDM uses a GUI, it requires that you access it from a PC using a supported web browser. Go to the Cisco Router and Security Device Manager (SDM) User Guide for the Cisco 7200 VXR and Cisco 7301 Routers documentation for more information. The show version command displays the release of Cisco IOS software that is available on the router.If the remote end of the WAN connection is connected and properly configured, the AutoInstall process begins. Perform the following step to complete this task. If you fail to do this, your configuration will be lost the next time you reload the router. These parameters are used for controlling system-wide settings. Complete the following steps to enter the global parameters: The following information appears after about 30 seconds.

The system stores the present parameter measurements for both temperature and DC voltage in NVRAM so you can retrieve them later as a report of the last shutdown parameters. Immediate operator action is required. All DC power remains disabled until you toggle the power switch. Before any shutdown, the system logs the status of monitored parameters in NVRAM so you can retrieve it later to help determine the cause of the problem. You can also retrieve and display environmental status reports with the show environment, show environment all, show environment last, and show environment table commands. Parameters are measured and reporting functions are updated every 60 seconds. A brief description of each of these commands follows. Overtemperature conditions can occur if the system is drawing in the exhaust air of other equipment. Ensure adequate clearance around the sides of the chassis so that cooling air can flow through the chassis interior unimpeded and exhaust air exits the chassis and is not drawn into the inlet vent of another device. The report displays parameters that are out of the normal values. No parameters are displayed if the system status is normal. The example that follows shows the display for a system in which all monitored parameters are within normal range: Following is a sample overvoltage warning: Air temperature is measured and displayed, and the DC voltage supplied by the power supply is also displayed. These thresholds are related to those listed in Table 3-1 and Table 3-2. The display also lists the shutdown threshold for the system. The show environment all command also displays a report showing which power supply slots are occupied and which are empty. The system continues to operate if a fan fails. When a fan fails, the system displays the following message: The LEDs on the port adapter go on and off in irregular sequence. They may go on, go out, and go on again for a short time. On the router, the green STATUS LED comes on and stays on.

To configure the interface parameters, you need your interface network addresses and subnet mask information. Consult with your network administrator for this information. Following are three examples of three different interfaces that might be used. Follow these steps to configure an ATM interface: Enter yes to configure for extended AppleTalk networks, and then enter the cable range number. Enter the zone name and any other additional zones that are associated with your local zone: Follow these steps to configure Fast Ethernet interfaces: Enter yes to configure for extended AppleTalk networks, and then enter the cable range number. Enter the zone name and any other additional zones that are associated with your local zone: Follow these steps to configure synchronous serial interfaces: Enter yes to configure for extended AppleTalk networks, and then enter the cable range number. Enter the zone name and any other additional zones that are associated with your local zone: You can use the setup command if you want to modify the parameters after the initial configuration. To perform more complex configurations, use the configure command. Complete the following steps to configure the router manually: Press Ctrl-Z (hold down the Control key while you press Z ) or enter end to exit configuration mode and return to the EXEC command interpreter. To see a list of the configuration commands available to you, enter.All Cisco IOS images for the Cisco 7301 platform use CPU-core 0. CPU-core 1 allows acceleration of specific feature sets via separately purchased special software. As of Cisco IOS Release 12.3(14)YM, multi-processor forwarding (MPF) accelerates the following broadband features: L2TP Access Concentrator (LAC), L2TP Network Server (LNS), and PPP Terminated Aggregation (PTA). Port adapters are not supported in the multi-processor forwarding (MPF) path on processor 1. To have all packets forwarded by processor 0, use the no ip mpf command.

When you see this information, you have successfully booted your router: On subsequent uses of the setup facility, the script begins with a System Configuration Dialog as shown in the following example. Method Status ProtocolFor Internet Protocol (IP)-only installations, you can accept the default values for most of the questions. A typical configuration using IP, IPX, and AppleTalk follows and continues through Step 8: It provides a means to access and set configuration and run-time parameters of routers and communication servers. SNMP defines a set of functions that can be used to monitor and control network elements. If you are using IP routing, you must also select an interior routing protocol. You can specify only one of two interior routing protocols to operate on your system using the setup facility: Interior Gateway Routing Protocol (IGRP) or Routing Information Protocol (RIP). Only IP, IPX, and AppleTalk are the selected protocols for this example. This is done by using the media-type interface command: Changing the speed and duplex of a Cisco 7301 router Gigabit Ethernet interface is done using the speed and duplex interface commands. This is useful for connecting to other Gigabit Ethernet equipment that does not support IEEE 802.1z autonegotiation. Any speed or duplex commands are ignored while using this media-type mode, even if present in the configuration (for an example, see output from show running-config ). For example, it shows the detected link status, speed, and duplex, and also determines the current status of autonegotiation and the link partners' abilities (if it is an autonegotiation-capable interface). The show controller command is a very powerful debugging aid, especially for Cisco engineers should you need help in debugging a problem. If you have any problems with your Gigabit Ethernet interfaces, you will need to provide this information to Cisco for analysis.

If bit 13 is set, the system boots the boot helper image found in boot flash memory without any retries. To form the boot filename, the server starts with Cisco and links the octal equivalent of the boot field number, a dash, and the image name. Table C-3 lists the default boot filenames or actions. It disables the bootstrap messages at startup. Setting bit 8 (the factory default) causes the processor to ignore the console Break key. Clearing bit 8 causes the processor to interpret Break as a command to force the system into the bootstrap monitor, halting normal operation. A Break can be sent in the first sixty seconds while the system reboots, regardless of the configuration settings. Setting bit 10 causes the processor to use all zeros; clearing bit 10 (the factory default) causes the processor to use all ones. B it 10 interacts with bit 14, which controls the network and subnet portions of the IP broadcast address. Table C-4 shows the combined effect of bit 10 and bit 14. Table C-5 shows the bit settings for the four available baud rates. (The factory set default baud rate is 9600.) If boot commands are in the configuration file, the router software processes each boot command in sequence until the process is successful or the end of the list is reached. If the end of the list is reached without a file being successfully booted, the router will retry the netboot commands up to six times if bit 13 of the configuration register is set, otherwise it will load the operating system software available in ROMmon. The default setting for bit 13 is 0. If bit 13 is set, the system boots the boot helper image found in boot flash memory without any retries. See the following sample output: See the following sample output: See the following sample output: See the following sample output. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices.

The purpose of this guide is to enable the safe and efficient installation of the Cisco 7301 router. Cisco 7301 Installation and Configuration Guide. The users of this guide should be familiar with electronic circuitry and wiring practices and have experience as electronic or electromechanical technicians. Users of this guide should also have experience in installing high-end networking equipment. CONSERVEZ CES INFORMATIONS Cisco 7301 Installation and Configuration Guide OL-5418-07. GUARDE ESTAS INSTRUCCIONES Cisco 7301 Installation and Configuration Guide OL-5418-07. SPARA DESSA ANVISNINGAR Cisco 7301 Installation and Configuration Guide OL-5418-07. GEM DISSE ANVISNINGER Cisco 7301 Installation and Configuration Guide viii OL-5418-07. To access Software Advisor, click Log In at Cisco.com and go to Support, Tools and Resources. Access to this tool is limited to users with Cisco.com login accounts. Statement 1071. Cisco 7301 Hardware Overview This section provides you with an overview of the hardware including LEDs, front and rear views, and interior part identification. Cisco 7301 Installation and Configuration Guide OL-5418-07. The processor also performs some memory and environmental monitoring functions. Do not discard the shipping container. You need the container if you move or ship the Cisco 7301 router in the future. Accessories: The following accessories might arrive in separate shipping containers: Rack-mount and Two rack-mount brackets, one cable-management bracket, four 12-24 x 0.5-in. You must install the SFP GBIC module. It is shipped separately to prevent damage during shipment. After reading this section, use the installation instructions in the “Installing. Do not stare into beams or view directly with optical instruments. Statement 1051 Class 1 laser product. Statement 1008 Warning Class 1 LED product. Statement 1027 Warning Cisco 7301 Installation and Configuration Guide 1-10 OL-5418-07.

To enable processor 1, use the ip mpf command. They are listed below along with sample output. Use these commands to verify the MPF installation. This command is supported only for physical interfaces. There is no support for virtual access interface. If you fail to do this, your configuration will be lost the next time you reload the router. These publications contain additional information on using the configure command. You can choose to configure the system to point to the upgradable ROMmon image. At bootup, the system starts with the ReadOnly image and then, if configured, jumps to the upgradeable ROMmon image. If the upgradeable ROMmon image fails to boot, the router will mark this ROMmon image as invalid and reverts to the ReadOnly ROMmon image. If the ROMmon-executing process is interrupted, the system interprets this as a bootup failure of the new ROMmon image. The router reverts to the ReadOnly image. Do not reset the router when it is doing an initial bootup. See the following examples for information shown in the output of the show rom-monitor or showmon commands: The enable secret password is encrypted, however, and must be replaced with a new enable secret password. You might need to reload the system image by power cycling the router. This allows you to log in without using a password and to display the startup configuration passwords. Note the value for use later and proceed to Step 6. If you cannot log in to the router at all, go to the next step. Proceed to Step 6. If Break is disabled, power cycle the router (turn the router off or unplug the power cord, and then restore power after waiting 30 seconds). Then proceed to Step 5. The user EXEC prompt is displayed as follows: Then enter the show startup-config command to display the passwords in the configuration file as follows: The passwords displayed look something like this: The enable and console login passwords may be encrypted or clear text.

Proceed to the next step to replace an enable secret, console login, or enable password. If there is no enable secret password, note the enable and console login passwords, if they are not encrypted, and proceed to Step 17. Failure to follow the steps as shown might cause you to erase your router configuration. This action allows you to modify or replace passwords in the configuration. You can remove individual passwords by using the no form of the above commands. For example, entering the no enable secret command removes the enable secret password. If you omit this step, all interfaces are administratively shut down and unavailable when the router is restarted. If you skipped You can also use the show diag slot command to display information about the port adapter slot. Note that slot 0 is reserved for the native Gigabit Ethernet ports: To select either optical Gigabit Ethernet or copper Gigabit Ethernet ports, use the media-type command. Following the table is a more in-depth description of each setting. Table C-2 provides information about the bits settings. If you set the boot field value to 0, you must have a console port access to boot the operating system manually. Boot the operating system by entering the b command at the bootstrap prompt as follows: If no file is found in system Flash memory, the router attempts to netboot a default file with a name derived from the value of the boot field (for example, cisco2-7301). If the netboot attempt fails, the boot helper image in boot flash memory will boot up. If the end of the list is reached without a file being successfully booted, the router will retry the netboot commands up to six times if bit 13 of the configuration register is set, otherwise it will load the operating system software available in ROMmon. If bit 13 is not set, the router will continue to netboot images indefinitely. The default setting for bit 13 is 0.

Planning a proper location for the Cisco 7301 router and the layout of your equipment rack or wiring closet is essential for successful system operation. Equipment placed too close together or inadequately ventilated can cause system overtemperature conditions. Before installing the chassis in the rack, you must install a rack-mount bracket on each side of the front or rear of the chassis. To install the rack-mount and cable-management brackets on a Cisco 7301 router for a front rack-mount configuration, complete the following steps: Locate the threaded holes in the front sides of the chassis. Step 2 Using a Phillips screwdriver and the screw, thread and tighten the screw to the M4 x 20-mm cable-management bracket. These screws are not available from Cisco Systems; they are available from a commercial hardware vendor.See “Tools and Parts Required”. For example, if you are connecting. The Cisco 7301 router has three native Gigabit Ethernet interfaces and six physical Gigabit Ethernet ports, three RJ-45 ports (copper) and three SFP GBIC ports (optical). Only three of the six ports can be in use at any one time. Cisco Systems does not supply Category 5 UTP cables; these cables are available commercially. Appendix A, “Specifications,”. A practical means of performing this conditioning is to use a device called a mode-conditioning patch cord. Cisco 7301 Installation and Configuration Guide 2-19 OL-5418-07. Connect TX to RX and RX to TX. Cisco 7301 Installation and Configuration Guide 2-20 OL-5418-07. The alarm port cable is not provided by Cisco Systems. Insert the cable connector into the alarm port. The cable connector cannot be incorrectly inserted into the alarm port. Connecting Power This section provides the procedures for connecting AC-input and DC-input power to your Cisco 7301 router. Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit.

Warning When you install the unit, the ground connection must always be made first and disconnected last. Statement 1046 Cisco 7301 Installation and Configuration Guide 2-23 OL-5418-07. The plug allows you Step 4 to unplug the DC wires from the power supply without having to unscrew the leads. Step 7 Press the power switch to turn on the router. Step 8 For information on Cisco 7301 product specifications and power supply, refer to Cisco 7301 Router Data Sheet at the following URL: 611a.html After powering off the router, wait a minimum of 30 seconds before powering it on again. To configure a Cisco 7301 router from a console, you need to connect a terminal to the router console port. Functional Overview This section provides a functional overview of the Cisco 7301 router. The MAC address for the port adapter slot in the Cisco 7301 is slot 0. You can remove a port adapter and insert it into another router without causing the MAC addresses to move around the network or be assigned to multiple devices. When you remove or insert a port adapter or service adapter in a Cisco 7301 router, the pins send signals to notify the system, which then performs as follows: Rapidly scans the system for configuration changes. Table 3-1 lists the typical temperature thresholds for the Cisco 7301 router, and Table 3-2 lists the DC power thresholds for the normal, warning, and critical (power supply-monitored) levels. You can also retrieve and display environmental status reports with the show environment, show environment all, show environment last, and show environment table commands. Checking Conditions Prior to System Startup Check the following conditions before you start your router: The port adapter is inserted in its slot and the port adapter latch is in the locked position. Complete the following steps to prepare your Cisco 7301 router for the AutoInstall process: Step 1 Attach the appropriate synchronous serial cable to synchronous serial interface 0 on the router.

This is done by using the media-type interface command:. Changing the speed and duplex of a Cisco 7301 router Gigabit Ethernet interface is done using the speed and duplex interface commands. Note Only one port adapter can be installed in the Cisco 7301 at one time. Following are three examples of three different interfaces that might be used. Configuring ATM Interfaces In the following example, an ATM interface in slot 1 is configured for an ATM LAN using IP. Cisco 7301 Installation and Configuration Guide 3-17 OL-5418-07. Cisco 7301 Installation and Configuration Guide 3-18 OL-5418-07. Cisco 7301 Installation and Configuration Guide. Complete the following steps to configure the router manually: Connect a console terminal to the console port. Processor board ID 74806813 SB-1 CPU at 700MHz, Implementation 1, Rev 0.2, 512KB L2 Cache 1 slot midplane, Version 3.0. See the following examples for. Note Changing Preferences to Choose the Other ROMmon Image To use the other ROMmon image, use one of the following commands to make the change depending on. Upgrade ROMMON corrupted.It is possible to recover the enable or console login password. The enable secret password is encrypted, Note however, and must be replaced with a new enable secret password. Log in to the router with the new or recovered passwords. Step 21 This completes the steps for recovering or replacing a lost enable, enable secret, or console login password. Cisco 7301 Installation and Configuration Guide 3-33 OL-5418-07. You can also use the show diag slot command to display information about the port adapter slot. Before you remove or replace any equipment, be sure to read the “Electrical Equipment. However, if you choose to power off the router to remove or install a port adapter, turn the power switch to the off position and then remove the power cable. Step 4 Locate the port adapter slot guides inside the Cisco 7301 router. They are near the top, and are recessed Step 5 about one-half inch.

The port adapter must slide into the slot guides under the chassis lid. Do not allow the port adapter Caution components to come in contact with the system board or the port adapter could be damaged. The memory configuration you ordered is installed in the Cisco 7301 router. During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly Warning touch the backplane with your hand or any metal tool, or you could shock yourself. Note Use only memory purchased form Cisco Systems. Note Attach an ESD-preventative wrist strap between you and an unpainted router surface. Step 1 Locate the SODIMMs. Follow these instructions to replace the cover: Figure 4-5 Inserting the Screws and Replacing the Cover. If you are unable to easily solve the problem, contact a customer service representative for assistance and further instructions. The STATUS LED turns green when the system boots to the Cisco IOS state. If the system does not boot properly, call your local service representative. Cisco IOS release. If Cisco IOS does not boot, and the green STATUS LED is not displayed, contact a service representative. System does not. Contact a service representative.Troubleshooting the Cooling Subsystem Check the following to help isolate a problem with the cooling subsystem: Cisco 7301 Installation and Configuration Guide OL-5418-07. Cisco 7301 Installation and Configuration Guide OL-5418-07. Access Cisco.com on the web and if you are a registered Cisco.com user, click Login at the top right of the page. If you are not a registered Cisco.com user, you can register by clicking Register at the top right side of the Cisco.com page. For more detailed instructions on loading and maintaining system images and microcode, including boot helper images, refer to the Cisco IOS Configuration Fundamentals Configuration Guide, which is available on Cisco.com. Note Software Requirements The minimum software requirement for the Cisco 7301 router is Cisco IOS Release 12.

2(11)YZ and Release 12.2(13)B. To check the minimum software requirements of Cisco IOS software with the hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com. You can also access the tool by pointing your browser directly to launch.html. Choose a product family or enter a specific product number to search for the minimum supported software release needed for your hardware. The RJ-45 ports support IEEE 802.3ab (Gigabit Ethernet) and IEEE 802.3u (Fast Ethernet) interfaces compliant with 10BASET, 100BASETX, and 1000BASET specifications. Table A-8 provides information about asynchronous device cabling options. Cisco 7301 Installation and Configuration Guide OL-5418-07. To use this pin, you must create a customized cable. Cisco 7301 Installation and Configuration Guide OL-5418-07. VARNING Eksplosionsfara vid felaktigt batteribyte. Cisco 7301 Installation and Configuration Guide OL-5418-07. The CompactFlash Disk provides increased Flash-based memory space—64 MB to 128 MB—for storage of system configuration files, Cisco IOS software images, and other types of system-related files. Table B-1 provides memory information for the CompactFlash Disk. The default software image is the CISCOxxx image (where xxx is a filename assigned by the system, if you do not enter a specific filename). Change the boot variables in your configuration file to point to the new Cisco IOS image in your Step 4 CompactFlash Disk. (See the preceding section, “Boot Environment. The following partial output of the show file systems command shows a sample system with a CompactFlash Disk—called disk0:—installed in slot 0:. If you want to save data that is currently on your CompactFlash Disk, copy the data to a TFTP server or to another CompactFlash Cisco 7301 Installation and Configuration Guide OL-5418-07.

cisco 6945 manual

If you do not retrieve the call within a certain amount of time (set by your system administrator), a reminder tone will sound on your phone, at which time you can resume the call by pressing the Resume soft key or by retrieving it from another phone. If you do not retrieve or resume the call within a specified amount of time (set by your system administrator) after the reminder tone, the call will be directed to another destination (set up by your system administrator), such as voicemail. You have a limited time to retrieve the parked call before it reverts to ringing at the original number. You have a limited time to retrieve a parked call before it reverts to ringing at the original number. If multiple calls are available for pick up, your phone picks up the oldest call first (the call that has been ringing for the longest time). Your system administrator may also change the function of the Pickup key to operate as Directed Pickup of a specific extension instead of local group pickup. In this configuration, the calls from you local group can be picked up by pressing the GPickUp key followed by the Star key. If the call rings, press the Answer soft key to connect to the call. The older call is placed on hold. Example: If you have a holding call on Line 1 and an active call on Line 2, pressing the Line 1 button makes the Line 1 call active (resumes it from hold) and automatically puts the Line 2 call on hold. You will hear a confirmation beep. Dial the number exactly as if you were placing a call to that number. Remember to include locally required prefix numbers. The phone display is updated to show that calls will be forwarded. The Mute button lights, indicating that the other party cannot hear you. All other participants can join the meeting by dialing into the MeetMe conference number. Also, you can set separate a ringtone for each number when there are multiple phone numbers on the phone. Barge converts the call into a conference.

• cisco 6945 manual, cisco 6945 user guide, cisco cp-6945 manual, cisco 6945 user manual, cisco cp 6945 user manual, cisco 6945 phone manual, cisco phone cp-6945 manual, cisco 6945 manual, cisco 6945 manual, cisco 7945 manual pdf, cisco 7945 manual user guide, cisco 6945 manual pdf, cisco 6945 manual download, cisco 6945 manual free, cisco 6945 manual software, cisco 6945 manual.

The Cisco IP Phone 6945 has four lines. Also, shows dedicated phone line labels. Allows you to scroll through menus, highlight items, and display speed dials list if you press down when the phone is on-hook. Display phone numbers from your Placed Calls if you press up when the phone is on-hook. When the headset is on, the button is lit. When the speakerphone is on, the button is lit. If not on a call, displays line text label and other information such as placed calls, speed dials, and phone menu listings. An extension protrudes from the top of the rotated tab. Return the handset to the handset rest. It is recommended to configure the dn as dual-line dn and the huntstop channel under the dn. The second channel on the dn can only be used for call transfer or conference. Consult your system administrator for more information. Soft keys are displayed along the bottom of the LCD screen and activated using the corresponding buttons. Soft keys can change according to the state of the phone. Use the backspace soft key to erase digits that you entered incorrectly. Resumes call on hold. To decrease contrast, press the down arrow. Otherwise, calls ring normally and you must manually answer them. Otherwise, calls ring normally and you must manually answer them. The Call History screen displays only the missed calls on the selected line. With this type of directed call, you can monitor the status of the line (in-use, idle, or in Do Not Disturb state) using Line Status indicators. You retrieve the call at another phone by dialing a park retrieval prefix number (provided by your system administrator), then dialing the Directed Call number you used to park the call. For the duration of the call, your phone displays the call park number where the system stored the call.

5 (SCCP and SIP) Softkeys Phone Screen Icons Buttons Common Phone Tasks Softkeys All Calls Lists all missed, placed, and received calls. Answer Answer a call. Apply Confirm a ringtone selection. Call Initiate a call. Callback Receive notification when a busy extension becomes available. Cancel Cancel an action or exit a screen without applying changes. Clear Clear all values. Delete Delete an entry from Call History. Del Call Delete a call from Call History. Details Opens the Details for a multiparty call in the Missed, Placed, and Received Call records. Dial Dial a selected number. Divert Send or redirect a call to voicemail or to a predetermined phone number. Edit Modify a name or email address. EditDial Modify a number. Exit Return to the previous screen. GPickup Answer a call that is ringing in another group or on another line. Log Out Sign out of Personal Directory. Meet Me Host a Meet Me conference call. Missed Open the record of missed calls.Common Phone Tasks Place a call Go off-hook before or after dialing a number. Redial a number Press Redial. Switch to handset during a call Pick up the handset. Switch to speaker or headset during a call Press or, then hang up the handset. Mute and un-mute a call Press. Hold and resume a call Press, to hold. Press Resume to resume the held call. Transfer a call to new number Press, enter the number, then press it again. Place an intercom call Press the Intercom button, then enter a number if necessary. Speak after you hear the tone. Start a standard conference call Press, dial the participant, then press it again. Silence the ring for an incoming call Press the Volume button down once. Sign up now. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R). All rights reserved. For details on your phones and phone features, see the user guide. To decrease contrast, press the down arrow. You will hear a confirmation beep.

To barge, press the red session button for the remote in-use call on the shared line. Visual confirmation displays briefly. Signing out of a hunt group does not prevent non-hunt group calls from ringing your phone. Depending on your setup, your phone can support the following speed-dial features: Fast Dial codes can be assigned to phone numbers or Personal Address Book entries. The call is placed on hold. The call is placed on hold. It is recommended to configure the dn as dual-line dn and the huntstop channel under the dn. The second channel on the dn can only be used for call transfer or conference. Your company determines the voicemail system your phone uses. The stutter tone is line-specific. You hear it only when using the line that has a waiting message. Speakerphone button 2. Phone display 11. Keypad 3. Programmable feature buttons 12. Mute button 4. Softkey buttons 13. Volume button 5. Transfer button 14. Messages button 6. The retrieving phone must also be on the Cisco phone system. If you are on an active call at your phone, you can park the call to a call park extension by pressing the Park button on the bottom of the screen. There are different methods to pick up a call, depending on your group assignment and the permissions you have been given. Outside calls still hear the Standard greeting. Also inclusive of AV support, Conferencing support and Digital Signage. Also inclusive of Facilities and operational systems. With this in mind, online instructions have been provided on how to use these functions and services. The telephones provided by Voice Services offer a broad range of functions and built in features. Please click on the appropriate link below on how to use your telephone. Additional links below provide instructions for the system's more popular features. OL-20187-01 Q UICK R EFERENCE Cisco Unified IP Phone 6921, 6941, 6945, and 6961 for Cisco Unified Communications Manager 8.

5 Divert. 6 Forward All. 7 Hold. 8 Conference. 9 Transfer. Manuals and user guide free PDF downloads for Cisco CP-3911 - Unified SIP Phone 3911 VoIP. Cisco Unified IP Phone User Guide for Cisco Unified Communications. Manager 8.6 (SCCP and SIP). For Cisco Unified IP Phone 6921, 6941, 6945, and 6961. Cisco Systems Amplified Phone Cisco CP 9951. 0 Solutions. I am lookingfor a manual for a Cisco 3844-13-1086. Cisco Systems IP Phone CP 6921. All rights reserved.Reload to refresh your session. Reload to refresh your session. Now you can huddle happy in smaller rooms and connect easy in conference rooms whatever video collaboration software you use Brilliant audio without interruptions. And the Trio C60 plays nicely with everyone, delivering native experiences on your favorite collaboration platforms. Give your workers the headset that will help them get more done, with style-meets comfort. Registrer deg for a fa med deg siste nytt fra Poly. Now you can huddle happy in smaller rooms and connect easy in conference rooms whatever video collaboration software you use Brilliant audio without interruptions. And the Trio C60 plays nicely with everyone, delivering native experiences on your favorite collaboration platforms. Give your workers the headset that will help them get more done, with style-meets comfort. Registrer deg for a fa med deg siste nytt fra Poly. Skip to primary navigation. Skip to secondary navigation. Skip to page content. Return to primary navigation. Skip to secondary navigation. Please note that you will need a PDF viewer to read these documents, such as Adobe Acrobat Reader. Secure your data. Staff Before you start. You will need a standard VOIP desk phone (Cisco 6921, 6961, 6945 or 7841) Instructions Phone model layouts Handset 6921 Handset 6945 Handset 7841 Do Not Hit the submit button immediately after entering the UserID. Please enter the user id and navigate down (using the Green down Navigate Button) to the PIN then enter PIN and then click submit.

Dial the number exactly as if you were placing a call to that number. Page 1 of 3. Cisco IP Phone 6921 User Quick Reference. Cisco CP-7975G-CCME. Cisco Jabber for iPhone5. Cisco Unified IP Phone 6921, 6941, and 6961 User Guide for Cisco Unified Communications Manager 8.0 (SCCP). Cisco manual gives you information.,cisco cp6921,cisco 6921 reset,cisco cp 6921 user guide,cisco phone manual 6921. Cisco Unified IP Phone 6921, 6941, 6945, and 6961 User Guide for Cisco.Entrega rapida e segura para todo o Brasil. Guide de l'utilisateur des telephones IP Cisco Unified 6921, 6941 et 6961 pour Cisco Unified Communications Manager 7.1 (SCCP). Americas Headquarters. Or How To Change The Ringtone And Idle Logo On The Cisco 7940G IP Phone. A Cisco IP Phone - I've got the 7940 model but from what I can tell, these steps should work on other similar ones also. Principales botones y su descripcion. Botones de teclas programadas. Transferencia de llamada. Review, learn about Cisco Unified IP Phone 8961 9951 and 9971 User Guide. Cisco VOIP Phone CP-6921-C-K9 Best prices and largest stock in Australia on. Americas Headquarters. Cisco Systems, Inc. 170 West Tasman Drive. San Jose, CA 95134-1706. USA. Tel: 408 526-4000. 800 553-NETS. This chapter describes the typical boot process for Cisco IP phones and the best practices for to configuring the network to support Voice over. San Jose, CA 95134-1706. USA. Tel: 408 526-4000. 800 553-NETS. Cisco 6921 Manual Online: Extension Mobility, Login, Logout. Cisco 6921 Administration Manual 210 pages. CP-7931G Using Cisco Extension Mobility. For the purposes of this exercise, we're using a Cisco CP-7960G. Do you have any guide for 6921 model. Name: Cisco Cp 6921 User Manual File size: 13 MB Date added: February 22, 2013. On Cisco Unified Call Manager Administration - Device - Phone, for CP-6921. Jabra, in conjunction with the Cisco platform, allows connectivity to any. QUICK START. Cisco Unified IP Phone 6921. 1 Dial. 2 Answer. 3 Mute. 4 Voicemail.

Press the up or down volume key located on the lower right hand side of the phone to increase or decrease the ringing volume or listening volume. After adjusting the listening volume, you will be prompted to save the new setting. Change the ring type. Press the Settings button. ? Select Preferences. ? Select Ringtone. ? Use the scroll key to select a ring type. ? Press the Play soft key to hear a sample of the selected ring type. ? Press Set and then press Apply to save your selection. ? Exit the directory menu. Contacts: DIRECTORIES Call History. You may view Missed, Received and Placed Calls by pressing the Directories button. ? To view Missed Calls, press the Directories button, Select the missed calls directory display the missed calls list. ? You can also press the up arrow on your blue navigation button to view call history. ? When you are finished, press the Exit soft key twice to exit the Directory menu. Page 3 Contacts are available on your IP Phone and can be created via the web GUI. Follow instructions below to program your contacts. To view them on your IP phone; press the Directories Button, then Personal Directory. When prompted to login; use the same username and PIN that you used to login to the CCM User Page (for example; JDoe and 123321). Contacts: Personal Directory is your own directory where you can store numbers via the User Options page. This is a secure directory which is only accessible by your phone and is not shared with rest of the organization. Page 12 Presented by Presented by To speed dial a Missed, Received, or a Placed call: o Press the directories button.To dial an external number. Press the More button, then Edit Dial soft key. Press the up arrow on the blue toggle button and enter a “9” then the Dial soft key to call an external number, “9” and “1” for long distance. Personal Directory: ? ? ? ? ?

Press the Directories button Use the navigation button or press 4 to select the Personal Directory Log in to the directory using your user ID and PIN. Search for your personal entries. Press Dial soft key to dial the selected number Note: Personal Directories are setup in the UCM User Options Menu. Instructions are later in the presentation. Corporate Directory. Press the Directories button. Use the Navigation button or press 5 to select the Corporate Directory. Use the Navigation button to enter the Last, First or Number fields search option, and press the Search soft key to find your selection. Use the Navigation button to find your listing. Press Dial soft key to dial the selected number To Remove a Speed Dial. BASIC CALL FEATURES Page 11 Page 4 Presented by Presented by Place a call. Lift the handset and dial the number. ? Press a line button and dial the number. ? Press the Speaker button and dial the number. ? Press the NewCall soft key and dial the number. Answer a call: ? Lift the handset. ? Press the line button associated with the call. ? Press the Answer soft key. End a call: ? Hang up the handset. ? Press the Speaker button. ? Press the EndCall soft key. Place a call on hold. While on a call, press the Hold key. ? To return to the call, press the Resume soft key. ? If multiple lines are on hold, use the scroll keys to select the desired line before you press Resume. Redial the most recently dialed number. Lift the handset and press the Redial soft key, or simply press the Redial soft key to activate the speakerphone. Forward All Calls: To forward all calls to another extension. Press the FwdAll soft key. You will hear two beeps. ? Enter the number to which you want to forward all your calls. A flashing right arrow will appear next to your phone number on the LCD to indicate that all calls are being forwarded. To cancel forward all calls: o Press the FwdAll soft key.

At first login you will be asked to change your PIN. Make a call To dial, lift the handset and enter a number. Or: a) Press the Line 1 button (your extension).Enter the extension number required. Speak privately with the dialled party. Press the Transfer button again to connect the third party. If there is no reply or the number is busy. Voicemail New message indicators: A solid red light on your handset. A stutter dial tone on the line (if enabled). A message waiting icon. To listen to messages, press the Messages button and follow the voice prompts. Alternatively press the Line button next to the voicemail icon, followed by the Messages button. Call hold To place a call on hold: Press the Hold button. Enter the phone number to which calls are to be forwarded. For calls to go directly to Voice Mail, press the Messages button. Call history To view your Call History. Press the Applications button. Select Call History. Select All Lines or the line that you want to view. Park call Parking a call allows the call to paused (parked) at one phone and retrieved at another. You will be reconnected to the call. Note: If the call is not retrieved within a specified time it will revert to the phone that parked it. Conference calls To create ad-hoc conference calls on the phone. The conference is initialized whilst on a call as follows: Press the Conference button. Dial the extension of the 3rd party you would like join the conference. Press the Conference button to introduce the 3rd party into Conference. Press Swap then Resume to return to the original call. Web access You can manage your phone via a web page including the configuration of call forwarding and the programming of speed dials. To access your personal User Web Page from an internet Browser: Go to User Page. Log on using your UserID and Password Use the drop down User Options list to manage your handset features.

It would also be really useful if we could discuss your feedback with you, so if you are happy to be contacted please include your UCL email address in 'Email' field below. Please note: We can only respond to UCL email addresses. And by having access to our ebooks online or by storing it on your computer, you have convenient answers with Cisco Cp 6941 User Guide. To get started finding Cisco Cp 6941 User Guide, you are right to find our website which has a comprehensive collection of manuals listed. Our library is the biggest of these that have literally hundreds of thousands of different products represented. I get my most wanted eBook Many thanks If there is a survey it only takes 5 minutes, try any survey which works for you. Press the messages key on your phone. ? Follow the recorded instruction to record your name, record your greeting(s), and reset your password. Wait until the system tells you that you have completed enrollment before hanging up. ? You can enter up to three numbers per entry. Home, Work and Mobile. Do not forget to add the outside access code 9. For example; Anne Weston below is programmed with 92819538899 where 9 is the outside line access code. Directory: You can also search a user’s phone number and create a contact by logging into the web. To search for entries in the Phone direcotry; follow instructions below. Click on Directory Tab. Accessing Voice Mail: From Your Internal Phone. From Another Internal IP Phone. From an External Phone. Page 1 Page 14 Presented by Presented by. You play a voice message by opening the attachment. ? If you would like to forward the voicemail to someone, simply forward the email. Click Add New to add a new entry. Voice Mail Features: Fill out information and assign a Speed Dial if needed. PHONE CONTROLS Mute a call. Press the Mute button. ? To turn off mute, press Mute again or lift the handset. Change the volume: Page 13 Page 2 Presented by Presented by ? ?

You will hear two beeps, The flashing arrow will no longer display next to your phone number on the LCD, indicating that forward all calls in not active. Page 5 ? ? You can configure up to 3 Speed Dials that will appear on the phone the rest 196 entries can be setup as Abbreviated Dialing Numbers. Press Save. Page 10 Presented by Presented by. Check the Forward all calls and either enter the phone number including the 9 to dial out, or select the voicemail option from the dropdown menu. Please add 9 if it’s an external call and 91 in front of the number if it’s a Long Distance Number. ? The Speed Dial numbers will display on your phone as text. ? Press Save. Change between handset and speakerphone during a call. To move a handset call to speakerphone, press the Speaker button and hang up the handset. ? To move a speakerphone call to your handset, lift your handset. Call Transfer: To transfer without talking to the transfer recipient. During a call, press the Transfer button. This places the call on hold. ? Dial the transfer recipient’s number. ? Press Transfer again. To talk to the transfer recipient before transferring the call. During a call, press the Transfer button. ? Dial the transfer recipient’s number. ? If the recipient accepts the transferred call, press Transfer. ? If you decide you do not want to complete the transfer, press Cancel, then Resume to return to the original call. Transfer a call directly into voicemail. Press Transfer soft key again. Call Park: To park a call. During a call, press the Park soft key to park a call. The system will display the park zone number (XX). Press Park again to park the call. To retrieve a parked call. Select the phone from which you wish to retrieve the parked call.DND (Do Not Disturb): The DND feature allows you to silence your ringer. ? While your phone is in the idle state, press the DND softkey. CONFERENCE CALLING Page 9 Page 6 Presented by Presented by Conference Calls: To place a conference call.

During a call, press the Conference button. This will automatically select a new line and place the other party on hold. ? Place a call to another person. ? When the call connects, press Conf soft key to add this person to the conference call. ? Repeat the first three steps to add people to the conference call. Accessing Cisco Phone User Options via the Web Browser: The Cisco User Options Web Browser Page allows the IP Phone users to manage their phone via an internet browser. Users can forward calls, configure speed dials, and configure personal address book entries for their phone. ? ? Conference List: Displays the list of callers on a conference call, with the ability to select and remove callers from the conference call. To Activate Conference List. While on a Conference Call, press the Details softkey. ? You can then highlight the caller you want to disconnect from by pressing the Remove softkey. Using your browser, go to (hint: save as favorite after logging in). Enter your user name and password (example user name: JDoe for John Doe) and use your network password. Forwarding calls: ? Under General Setting on the Home Page Page 7 Page 8 Presented by Presented by We are a non-profit group that run this service to share documents. We need your help to maintenance and improve this website.